FireCADCalc

Dry Sorbent Injection: Sodium Bicarbonate for SO₂ and HCl

Sodium bicarbonate for dry sorbent injection from the SO₂ and HCl loads, the removal wanted and the stoichiometric ratio (2 NaHCO₃ per SO₂, 1 per HCl).

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationDistillery and ethanolStack and chimneyDust collector (ESP, bag filter, cyclone)

Inputs

Examples: Biomass boilerHCl only

At least 1: below that the sorbent fed cannot remove the SO₂ and HCl asked for.

Results

Bicarbonate decomposes to reactive soda above about 140 °C; finer milling raises utilisation. Residue mixes with fly ash.

Stoichiometric NaHCO₃39.402kg/h
NaHCO₃ fed47.282kg/h
Sodium residue (Na₂SO₄ + NaCl, approx.)32.381kg/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Biomass boiler. The inputs, in the units selected above:

InputValue
Flue gas flow (dry, normal)100,000 Nm³/h
SO₂ at the inlet (dry)800.00 mg/Nm³
HCl at the inlet (dry)150.00 mg/Nm³
SO₂ removal70.000 %
HCl removal90.000 %
Stoichiometric ratio (sorbent / stoichiometric for removal)1.3000 -

Applying the formula below gives:

ResultValue
Stoichiometric NaHCO₃177.98 kg/h
NaHCO₃ fed231.38 kg/h
Sodium residue (Na₂SO₄ + NaCl, approx.)179.49 kg/h

Open this example in the calculator and change any input.

Formula

\(\dot m_{st} = (2\eta_{SO_2}\dot n_{SO_2} + \eta_{HCl}\dot n_{HCl})M_{NaHCO_3}, \quad \dot m = SR\,\dot m_{st}\)

\(\dot m_{res} = \eta_{SO_2}\dot n_{SO_2} M_{Na_2SO_4} + \eta_{HCl}\dot n_{HCl} M_{NaCl} + \frac{(SR - 1)\,\dot m_{st}}{2 M_{NaHCO_3}} M_{Na_2CO_3}, \quad \dot n_i = \frac{\dot V_n c_i}{M_i}\)

Variables

Symbol Meaning SI unit
\(\dot V_n\) Flue gas flow (dry, normal) Nm³/s
\(c_{SO_2}\) SO₂ at the inlet (dry) kg/m³
\(c_{HCl}\) HCl at the inlet (dry) kg/m³
\(\eta_{SO_2}\) SO₂ removal -
\(\eta_{HCl}\) HCl removal -
\(SR\) Stoichiometric ratio (sorbent / stoichiometric for removal) -
\(\dot m_{st}\) Stoichiometric NaHCO₃ kg/s
\(\dot m\) NaHCO₃ fed kg/s
\(\dot m_{res}\) Sodium residue (Na₂SO₄ + NaCl, approx.) kg/s
\(\dot n_{SO_2}\), \(\dot n_{HCl}\) molar flows of SO₂ and HCl at the inlet kmol/s
\(M_i\) molar masses (IUPAC) kg/kmol

Method and standards

Stoichiometry with IUPAC molar masses: two NaHCO₃ per SO₂ removed and one per HCl removed. The residue counts the Na₂SO₄ and NaCl formed and the excess bicarbonate as Na₂CO₃ (two NaHCO₃ give one Na₂CO₃ on heating).

Where it is used

  • Biomass and slop boiler acid gas control.
  • Reagent budgets.

Common mistakes

  • SO₂ ppm used as mg/Nm³.

Assumptions and limits

  • Dry, normal basis. The concentrations are at the actual O₂, matching the actual dry gas flow; values corrected to a reference O₂ must be converted back first.
  • The stoichiometric ratio must be at least 1.

References

  • Stoichiometry 2 NaHCO₃ + SO₂ + ½ O₂ → Na₂SO₄ + 2 CO₂ + H₂O; NaHCO₃ + HCl → NaCl + H₂O + CO₂

Questions and answers

Why two moles per SO₂?

Each SO₂ takes two sodium atoms to form sodium sulphate.

Stoichiometric ratio?

More than 1 because not all sorbent reacts in the short contact time.

Bicarbonate or lime?

Bicarbonate reacts faster and better with HCl; lime is cheaper.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.