Worked example
Example: Biomass boiler. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Flue gas flow (dry, normal) | 100,000 Nm³/h |
| SO₂ at the inlet (dry) | 800.00 mg/Nm³ |
| HCl at the inlet (dry) | 150.00 mg/Nm³ |
| SO₂ removal | 70.000 % |
| HCl removal | 90.000 % |
| Stoichiometric ratio (sorbent / stoichiometric for removal) | 1.3000 - |
Applying the formula below gives:
| Result | Value |
|---|---|
| Stoichiometric NaHCO₃ | 177.98 kg/h |
| NaHCO₃ fed | 231.38 kg/h |
| Sodium residue (Na₂SO₄ + NaCl, approx.) | 179.49 kg/h |
Open this example in the calculator and change any input.
Formula
\(\dot m_{st} = (2\eta_{SO_2}\dot n_{SO_2} + \eta_{HCl}\dot n_{HCl})M_{NaHCO_3}, \quad \dot m = SR\,\dot m_{st}\)
\(\dot m_{res} = \eta_{SO_2}\dot n_{SO_2} M_{Na_2SO_4} + \eta_{HCl}\dot n_{HCl} M_{NaCl} + \frac{(SR - 1)\,\dot m_{st}}{2 M_{NaHCO_3}} M_{Na_2CO_3}, \quad \dot n_i = \frac{\dot V_n c_i}{M_i}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(\dot V_n\) | Flue gas flow (dry, normal) | Nm³/s |
| \(c_{SO_2}\) | SO₂ at the inlet (dry) | kg/m³ |
| \(c_{HCl}\) | HCl at the inlet (dry) | kg/m³ |
| \(\eta_{SO_2}\) | SO₂ removal | - |
| \(\eta_{HCl}\) | HCl removal | - |
| \(SR\) | Stoichiometric ratio (sorbent / stoichiometric for removal) | - |
| \(\dot m_{st}\) | Stoichiometric NaHCO₃ | kg/s |
| \(\dot m\) | NaHCO₃ fed | kg/s |
| \(\dot m_{res}\) | Sodium residue (Na₂SO₄ + NaCl, approx.) | kg/s |
| \(\dot n_{SO_2}\), \(\dot n_{HCl}\) | molar flows of SO₂ and HCl at the inlet | kmol/s |
| \(M_i\) | molar masses (IUPAC) | kg/kmol |
Method and standards
Stoichiometry with IUPAC molar masses: two NaHCO₃ per SO₂ removed and one per HCl removed. The residue counts the Na₂SO₄ and NaCl formed and the excess bicarbonate as Na₂CO₃ (two NaHCO₃ give one Na₂CO₃ on heating).
Where it is used
- Biomass and slop boiler acid gas control.
- Reagent budgets.
Common mistakes
- SO₂ ppm used as mg/Nm³.
Assumptions and limits
- Dry, normal basis. The concentrations are at the actual O₂, matching the actual dry gas flow; values corrected to a reference O₂ must be converted back first.
- The stoichiometric ratio must be at least 1.
References
- Stoichiometry 2 NaHCO₃ + SO₂ + ½ O₂ → Na₂SO₄ + 2 CO₂ + H₂O; NaHCO₃ + HCl → NaCl + H₂O + CO₂
Questions and answers
Why two moles per SO₂?
Each SO₂ takes two sodium atoms to form sodium sulphate.
Stoichiometric ratio?
More than 1 because not all sorbent reacts in the short contact time.
Bicarbonate or lime?
Bicarbonate reacts faster and better with HCl; lime is cheaper.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.