FireCADCalc

Limestone for SO₂ Capture (Ca/S Ratio)

Limestone feed for in-bed or dry SO₂ capture from the fuel sulphur, Ca/S molar ratio and limestone purity, with the SO₂ left and the CaSO₄ and CaO formed.

Thermal power plantSugar mill and cogenerationChemical and fertiliserPulp and paperBoiler

Inputs

Examples: CFBC 50 t/h, 0.5 % S, Ca/S 2.0, 92 % CaCO3, 90 % captureLignite 80 t/h, 3 % S, Ca/S 2.2, 88 %, 92 %Pet coke 10 t/h, 6 % S, Ca/S 1.8, 95 %, 90 %

From the boiler maker for the capture wanted; fluidised beds typically need 1.5–3.

Results

Limestone feed18.731t/h
Limestone per kg of fuel0.23414kg/kg
SO₂ formed from the fuel sulphur4,795.4kg/h
SO₂ leaving after capture383.63kg/h
CaSO₄ formed9,375.7kg/h
Unreacted CaO5,373.3kg/h
Inerts in the limestone (to the ash)2,247.7kg/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: CFBC 50 t/h, 0.5 % S, Ca/S 2.0, 92 % CaCO3, 90 % capture. The inputs, in the units selected above:

InputValue
Fuel firing rate50,000 kg/h
Sulphur in the fuel, as fired0.50000 %
Ca/S molar ratio2.0000 -
CaCO₃ in the limestone, by mass92.000 %
SO₂ capture efficiency90.000 %

Applying the formula below gives:

ResultValue
Limestone feed1.6966 t/h
Limestone per kg of fuel0.033933 kg/kg
SO₂ formed from the fuel sulphur499.52 kg/h
SO₂ leaving after capture49.952 kg/h
CaSO₄ formed955.40 kg/h
Unreacted CaO481.01 kg/h
Inerts in the limestone (to the ash)135.73 kg/h

Open this example in the calculator and change any input.

Formula

\(\dot n_S = \frac{\dot m_f\,S}{M_S} \qquad \dot m_{ls} = \frac{Ca/S\cdot \dot n_S\,M_{CaCO_3}}{x_{CaCO_3}} \qquad \dot m_{SO_2,0} = \dot n_S\,M_{SO_2} \qquad \dot m_{SO_2} = (1 - \eta_s)\,\dot m_{SO_2,0}\)

\(\dot m_{CaSO_4} = \eta_s\,\dot n_S\,M_{CaSO_4} \qquad \dot m_{CaO} = (Ca/S - \eta_s)\,\dot n_S\,M_{CaO} \qquad \dot m_{in} = (1 - x_{CaCO_3})\,\dot m_{ls}\)

Variables

Symbol Meaning SI unit
\(\dot m_f\) fuel firing rate kg/s
\(S\) sulphur in the fuel as fired –
\(Ca/S\) calcium to sulphur molar ratio –
\(x_{CaCO_3}\) CaCO₃ in the limestone by mass –
\(\eta_s\) SO₂ capture efficiency –
\(\dot m_{ls}\) limestone feed kg/s
\(\dot m_{ls}/\dot m_f\) limestone per kg of fuel kg/kg
\(\dot m_{SO_2,0}\) SO₂ formed from the fuel sulphur kg/s
\(\dot m_{SO_2}\) SO₂ leaving after capture kg/s
\(\dot m_{CaSO_4}\) CaSO₄ formed kg/s
\(\dot m_{CaO}\) unreacted CaO kg/s
\(\dot m_{in}\) inerts in the limestone, to the ash kg/s
\(\dot n_S\) sulphur, molar flow kmol/s
\(M_S\), \(M_{CaCO_3}\), \(M_{SO_2}\), \(M_{CaSO_4}\), \(M_{CaO}\) molar masses (32.06, 100.09, 64.06, 136.13, 56.08) kg/kmol

Method and standards

Stoichiometry of calcination and sulphation (CaCO₃ → CaO + CO₂; CaO + SO₂ + ½O₂ → CaSO₄) with IUPAC atomic weights. All fuel sulphur is taken to form SO₂.

Where it is used

  • Sizing limestone feed for AFBC and CFBC boilers.
  • Estimating extra ash and CO2 from limestone.
  • Planning sulphur capture for emission limits.

Common mistakes

  • Using limestone purity as CaCO3 when it includes MgCO3.
  • Assuming one Ca/S ratio for all limestones and bed temperatures.
  • Forgetting the extra ash in ash handling.

Assumptions and limits

  • Magnesium carbonate in dolomitic limestone also captures some SO₂; it is not counted.
  • CO₂ released by calcination is not included here (see the CO₂ emission factor).
  • The Ca/S needed for a capture efficiency depends on the bed, the limestone and the temperature; it is your input. The capture entered is checked only against Ca/S (capture cannot exceed it), not against a Ca/S–capture curve.
  • Sorbent ash is the CaSO₄ formed, the unreacted CaO and the limestone inerts together.

References

  • Reaction stoichiometry CaCO₃ + SO₂ + ½O₂ → CaSO₄ + CO₂; IUPAC atomic weights

Questions and answers

How much limestone does a CFBC boiler need?

Limestone = Ca/S × (sulphur ÷ 32.06) × 100.09 ÷ purity. 50 t/h of coal with 0.5 % sulphur at Ca/S 2 and 92 % CaCO₃ needs 1.70 t/h of limestone.

Why is Ca/S above 1?

Not all the lime reacts: a layer of sulphate blocks the inside of each particle. Fluidised beds typically need 1.5 to 3 times the stoichiometric calcium; the ratio for the capture wanted comes from the boiler maker.

Where does the unreacted lime go?

It leaves as CaO with the ash, with the CaSO₄ formed, and adds to the ash handling load.

Method and article reviewed by FireCAD engineering on 10 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.