Worked example
Example: CFBC 50 t/h, 0.5 % S, Ca/S 2.0, 92 % CaCO3, 90 % capture. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Fuel firing rate | 50,000 kg/h |
| Sulphur in the fuel, as fired | 0.50000 % |
| Ca/S molar ratio | 2.0000 - |
| CaCO₃ in the limestone, by mass | 92.000 % |
| SO₂ capture efficiency | 90.000 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| Limestone feed | 1.6966 t/h |
| Limestone per kg of fuel | 0.033933 kg/kg |
| SO₂ formed from the fuel sulphur | 499.52 kg/h |
| SO₂ leaving after capture | 49.952 kg/h |
| CaSO₄ formed | 955.40 kg/h |
| Unreacted CaO | 481.01 kg/h |
| Inerts in the limestone (to the ash) | 135.73 kg/h |
Open this example in the calculator and change any input.
Formula
\(\dot n_S = \frac{\dot m_f\,S}{M_S} \qquad \dot m_{ls} = \frac{Ca/S\cdot \dot n_S\,M_{CaCO_3}}{x_{CaCO_3}} \qquad \dot m_{SO_2,0} = \dot n_S\,M_{SO_2} \qquad \dot m_{SO_2} = (1 - \eta_s)\,\dot m_{SO_2,0}\)
\(\dot m_{CaSO_4} = \eta_s\,\dot n_S\,M_{CaSO_4} \qquad \dot m_{CaO} = (Ca/S - \eta_s)\,\dot n_S\,M_{CaO} \qquad \dot m_{in} = (1 - x_{CaCO_3})\,\dot m_{ls}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(\dot m_f\) | fuel firing rate | kg/s |
| \(S\) | sulphur in the fuel as fired | – |
| \(Ca/S\) | calcium to sulphur molar ratio | – |
| \(x_{CaCO_3}\) | CaCO₃ in the limestone by mass | – |
| \(\eta_s\) | SO₂ capture efficiency | – |
| \(\dot m_{ls}\) | limestone feed | kg/s |
| \(\dot m_{ls}/\dot m_f\) | limestone per kg of fuel | kg/kg |
| \(\dot m_{SO_2,0}\) | SO₂ formed from the fuel sulphur | kg/s |
| \(\dot m_{SO_2}\) | SO₂ leaving after capture | kg/s |
| \(\dot m_{CaSO_4}\) | CaSO₄ formed | kg/s |
| \(\dot m_{CaO}\) | unreacted CaO | kg/s |
| \(\dot m_{in}\) | inerts in the limestone, to the ash | kg/s |
| \(\dot n_S\) | sulphur, molar flow | kmol/s |
| \(M_S\), \(M_{CaCO_3}\), \(M_{SO_2}\), \(M_{CaSO_4}\), \(M_{CaO}\) | molar masses (32.06, 100.09, 64.06, 136.13, 56.08) | kg/kmol |
Method and standards
Stoichiometry of calcination and sulphation (CaCO₃ → CaO + CO₂; CaO + SO₂ + ½O₂ → CaSO₄) with IUPAC atomic weights. All fuel sulphur is taken to form SO₂.
Where it is used
- Sizing limestone feed for AFBC and CFBC boilers.
- Estimating extra ash and CO2 from limestone.
- Planning sulphur capture for emission limits.
Common mistakes
- Using limestone purity as CaCO3 when it includes MgCO3.
- Assuming one Ca/S ratio for all limestones and bed temperatures.
- Forgetting the extra ash in ash handling.
Assumptions and limits
- Magnesium carbonate in dolomitic limestone also captures some SO₂; it is not counted.
- CO₂ released by calcination is not included here (see the CO₂ emission factor).
- The Ca/S needed for a capture efficiency depends on the bed, the limestone and the temperature; it is your input. The capture entered is checked only against Ca/S (capture cannot exceed it), not against a Ca/S–capture curve.
- Sorbent ash is the CaSO₄ formed, the unreacted CaO and the limestone inerts together.
References
- Reaction stoichiometry CaCO₃ + SO₂ + ½O₂ → CaSO₄ + CO₂; IUPAC atomic weights
Questions and answers
How much limestone does a CFBC boiler need?
Limestone = Ca/S × (sulphur ÷ 32.06) × 100.09 ÷ purity. 50 t/h of coal with 0.5 % sulphur at Ca/S 2 and 92 % CaCO₃ needs 1.70 t/h of limestone.
Why is Ca/S above 1?
Not all the lime reacts: a layer of sulphate blocks the inside of each particle. Fluidised beds typically need 1.5 to 3 times the stoichiometric calcium; the ratio for the capture wanted comes from the boiler maker.
Where does the unreacted lime go?
It leaves as CaO with the ash, with the CaSO₄ formed, and adds to the ash handling load.
Method and article reviewed by FireCAD engineering on 10 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.