FireCADCalc

HCl in Flue Gas from Fuel Chlorine

HCl formed from the chlorine in a fuel (biomass, slop, coal) and its concentration in the flue gas, with the share of chlorine leaving as HCl rather than salts.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationDistillery and ethanolStack and chimney

Inputs

Examples: Biomass 0.3 % ClSlop concentrate

The rest stays as KCl / NaCl in ash and deposits. It depends on the fuel's potassium, sodium and sulphur; 60 % is a FireCAD starting value. Use measured or published data for your fuel.

Results

Chlorine also drives high-temperature corrosion of superheaters with potassium-rich ash.

HCl formed18.512kg/h
HCl concentration (dry, normal)185.12mg/Nm³
HCl by volume (dry)113.81ppm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Biomass 0.3 % Cl. The inputs, in the units selected above:

InputValue
Fuel fired10.000 t/h
Chlorine in the fuel (as fired)0.30000 %
Share of chlorine released as HCl60.000 %
Flue gas flow (dry, normal)100,000 Nm³/h

Applying the formula below gives:

ResultValue
HCl formed18.512 kg/h
HCl concentration (dry, normal)185.12 mg/Nm³
HCl by volume (dry)113.81 ppm

Open this example in the calculator and change any input.

Formula

\(\dot m_{HCl} = \dot m_f\,Cl\,f\,\frac{M_{HCl}}{M_{Cl}}, \quad c = \frac{\dot m_{HCl}}{\dot V_n}\)

Variables

Symbol Meaning SI unit
\(\dot m_f\) Fuel fired kg/s
\(Cl\) Chlorine in the fuel (as fired) -
\(f\) Share of chlorine released as HCl -
\(\dot V_n\) Flue gas flow (dry, normal) Nm³/s
\(\dot m_{HCl}\) HCl formed kg/s
\(c_{HCl}\) HCl concentration (dry, normal) kg/m³
\(y_{HCl}\) HCl by volume (dry) -

Method and standards

Mass balance of chlorine: the share released as HCl is converted with the molar masses of HCl and Cl; the volume fraction uses the ideal-gas molar volume at 0 °C and 101.325 kPa.

Where it is used

  • Emission estimates.
  • Acid gas control design.

Common mistakes

  • Chlorine on dry basis with as-fired fuel.

Assumptions and limits

  • Dry, normal basis, at the actual O₂ of the gas: not corrected to a reference O₂. Correct it with the emission O₂ correction calculator before comparing with a limit.
  • The flue gas flow is your input and is not checked against the fuel fired; take it from the combustion calculator for the same fuel and excess air.
  • The release share depends on the fuel; 60 % is a starting value, not a published figure.

References

  • Mass balance Cl → HCl (molar masses, IUPAC); ppm on the molar volume at 0 °C
  • 1 atm

Questions and answers

Does all chlorine become HCl?

No: much is captured as potassium and sodium chloride in ash, especially in biomass.

Why care?

HCl is regulated and corrosive below its dew point; chlorides attack superheaters.

Slop and husk?

Both can carry significant chlorine; analyse the fuel.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.