FireCADCalc

Cyclone Pressure Drop (Shepherd–Lapple)

Pressure drop of a cyclone or multiclone tube from its inlet and outlet dimensions, gas flow and density by the Shepherd and Lapple velocity-head method.

Thermal power plantSugar mill and cogenerationChemical and fertiliserPulp and paperBoilerDust collector (ESP, bag filter, cyclone)

Inputs

Examples: Cyclone 2 m³/s, inlet 0.5 x 0.25 m, outlet 0.5 m, 0.85 kg/m³Multiclone tube 0.12 m³/s, inlet 0.12 x 0.06 m, outlet 0.12 mCyclone with inlet vane, 5 m³/s, 0.8 x 0.4 m, outlet 0.8 m

16 for a plain tangential inlet; 7.5 with an inlet vane (Shepherd and Lapple, 1939).

Results

Shepherd and Lapple's method is empirical, accurate to about ±30 %; use the maker's figure for the final design.

Cyclone pressure drop51.347mmWC
Number of inlet velocity heads3.7500
Inlet velocity15.625m/s
Inlet velocity pressure13.692mmWC

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Cyclone 2 m³/s, inlet 0.5 x 0.25 m, outlet 0.5 m, 0.85 kg/m³. The inputs, in the units selected above:

InputValue
Gas flow through one cyclone (actual)7,200.0 m³/h
Gas density0.85000 kg/m³
Inlet height500.00 mm
Inlet width250.00 mm
Gas outlet (vortex finder) diameter500.00 mm
Shepherd–Lapple constant16.000 -

Applying the formula below gives:

ResultValue
Cyclone pressure drop88.756 mmWC
Number of inlet velocity heads8.0000
Inlet velocity16.000 m/s
Inlet velocity pressure11.095 mmWC

Open this example in the calculator and change any input.

Formula

\(v_i = \frac{Q}{a\,b} \qquad p_{d,i} = \frac{\rho\,v_i^2}{2} \qquad N_H = K\,\frac{a\,b}{D_e^2} \qquad \Delta p = N_H\,p_{d,i}\)

Variables

Symbol Meaning SI unit
\(Q\) gas flow through one cyclone m³/s
\(\rho\) gas density kg/m³
\(a\) inlet height m
\(b\) inlet width m
\(D_e\) gas outlet diameter m
\(K\) Shepherd–Lapple constant –
\(\Delta p\) cyclone pressure drop Pa
\(N_H\) number of inlet velocity heads –
\(v_i\) inlet velocity m/s
\(p_{d,i}\) inlet velocity pressure Pa

Method and standards

The velocity-head method of Shepherd and Lapple (Industrial and Engineering Chemistry, 1939 and 1940), widely used for preliminary cyclone design.

Where it is used

  • Sizing mechanical dust collectors and cyclones.
  • Estimating ID fan pressure for a cyclone.
  • Comparing cyclone designs.

Common mistakes

  • Using normal instead of actual gas density.
  • Ignoring the effect of dust load on pressure drop.
  • Using inlet velocity outside the design range.

Assumptions and limits

  • Clean gas; dust loading usually lowers the pressure drop slightly.
  • Empirical: accurate to about ±30 %; use the maker's figure for the final design.
  • Collection efficiency is not calculated here.

References

  • Shepherd and Lapple
  • Ind. Eng. Chem. 31 (1939) 972; 32 (1940) 605

Questions and answers

How is cyclone pressure drop calculated?

Δp = N_H·ρv_i²/2 with N_H = K·a·b/D_e². A cyclone with a 0.5 × 0.25 m inlet and 0.5 m outlet passing 2 m³/s of gas at 0.85 kg/m³ has an inlet velocity of 16 m/s, 8 velocity heads and a drop of 870 Pa.

What is K?

An empirical constant of Shepherd and Lapple: 16 for a plain tangential inlet and 7.5 with an inlet vane.

Is this for one tube of a multiclone?

Yes, enter the flow per tube and the tube's dimensions; the tubes are in parallel, so the drop is the same for the whole unit.

Method and article reviewed by FireCAD engineering on 10 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.