Worked example
Example: Air 10 000 Nm³/h at 2 bar(a), 150 °C. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Normal flow (0 °C, 1.01325 bar) | 10,000 Nm³/h |
| Molar mass of the gas | 28.960 kg/kmol |
| Line pressure (absolute) | 2.0000 bar |
| Line temperature | 150.00 °C |
| Compressibility factor | 1.0000 - |
Applying the formula below gives:
| Result | Value |
|---|---|
| Actual flow at line conditions | 7,848.4 m³/h |
| Mass flow | 12,921 kg/h |
| Standard flow (15 °C, 1.01325 bar) | 10,549 m³/h |
| Density at normal conditions | 1.2921 kg/m³ |
| Density at line conditions | 1.6463 kg/m³ |
Open this example in the calculator and change any input.
Formula
\(\rho_n = \frac{p_0 M}{R T_0}, \quad \rho = \frac{p M}{Z R T}\)
\(\dot m = \dot V_n \rho_n, \quad \dot V = \dot m / \rho\)
\(\dot V_s = \dot m / \rho_s \ (15\ °C)\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(\dot V_n\) | normal flow (0 °C, 1.01325 bar) | Nm³/s |
| \(M\) | molar mass | kg/kmol |
| \(p\) | line pressure, absolute | Pa |
| \(T\) | line temperature | K |
| \(Z\) | compressibility factor | - |
| \(p_0\) | normal pressure 101 325 Pa | Pa |
| \(T_0\) | normal temperature 273.15 K | K |
| \(R\) | universal gas constant | J/(kmol·K) |
| \(\rho_s\) | density at 15 °C, 1.01325 bar | kg/m³ |
| \(\dot V\) | actual flow | m³/s |
| \(\dot m\) | mass flow | kg/s |
| \(\dot V_s\) | standard flow at 15 °C | m³/s |
| \(\rho_n\) | density at normal conditions | kg/m³ |
| \(\rho\) | density at line conditions | kg/m³ |
Method and standards
Mass flow is the same in any units; normal and actual volumes differ by the density ratio from the ideal gas law (with Z at line conditions).
Where it is used
- Sizing fans, ducts and gas pipes.
- Converting gas meter readings.
- Comparing data sheets that use different reference conditions.
Common mistakes
- Using gauge pressure in the gas law.
- Mixing normal (0 °C) and standard (15 °C or 60 °F) volumes.
- Forgetting water vapour in wet flue gas changes M.
Assumptions and limits
- Ideal gas at the reference conditions; Z at line conditions.
- The FPS display unit "scfm" is the US standard cubic foot per minute (60 °F, 14.696 psia), converted from the normal state; it is about 5.6 % larger than ft³/min at 0 °C for the same mass flow.
References
- Ideal gas law
Questions and answers
What is 10 000 Nm³/h of air at 2 bar(a) and 150 °C in actual m³/h?
About 7 850 m³/h; it weighs 12 900 kg/h.
What are normal and standard conditions?
Here normal is 0 °C and 1.01325 bar, standard is 15 °C and 1.01325 bar; other references exist, so check which a document uses.
Why does a fan care about actual flow?
Fans move actual volume: hot gas at low pressure occupies far more volume than its normal flow suggests.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.