FireCADCalc

Sludge Dewatering Balance: Cake, Filtrate and Polymer

Mass balance of a belt press, filter press or centrifuge: cake mass and volume, filtrate flow and solids, solids capture and polymer use.

Sugar mill and cogenerationDistillery and ethanolRefinery and petrochemicalChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: Belt press, 3 % to 22 %Centrifuge, 4 % to 28 %

Results

Feed density taken as 1,000 kg/m³ and wash water excluded. Typical cake solids: belt press 15–25 %, centrifuge 20–30 %, filter press 30–45 %.

Dry solids fed3,000.0kg/d
Wet cake12.955t/d
Cake volume12.338m³/d
Filtrate flow87.045m³/d
Filtrate solids1,723.2mg/L
Polymer15.000kg/d

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Belt press, 3 % to 22 %. The inputs, in the units selected above:

InputValue
Feed sludge flow100.00 m³/d
Feed solids3.0000 %
Cake solids22.000 %
Solids capture95.000 %
Polymer dose (kg per tonne dry solids)5.0000 -
Cake bulk density1,050.0 kg/m³

Applying the formula below gives:

ResultValue
Dry solids fed3,000.0 kg/d
Wet cake12.955 t/d
Cake volume12.338 m³/d
Filtrate flow87.045 m³/d
Filtrate solids1,723.2 mg/L
Polymer15.000 kg/d

Open this example in the calculator and change any input.

Formula

\(\dot m_{DS} = Q_f\rho s_f, \quad \dot m_c = \frac{\eta_c\dot m_{DS}}{s_c}, \quad \dot V_f = \frac{Q_f\rho - \dot m_c}{\rho_w}, \quad TSS_f = \frac{(1 - \eta_c)\dot m_{DS}}{\dot V_f}\)

\(\dot V_c = \frac{\dot m_c}{\rho_c}, \quad \dot m_p = \frac{d_p\,\dot m_{DS}}{1000}\)

Variables

Symbol Meaning SI unit
\(Q_f\) Feed sludge flow m³/s
\(s_f\) Feed solids -
\(s_c\) Cake solids -
\(\eta_c\) Solids capture -
\(d_p\) Polymer dose (kg per tonne dry solids) -
\(\rho_c\) Cake bulk density kg/m³
\(\rho\) Feed sludge density, taken as 1 000 kg/m³
\(\rho_w\) Filtrate density, taken as 1 000 kg/m³
\(\dot m_{DS}\) Dry solids fed kg/s
\(\dot m_c\) Wet cake kg/s
\(\dot V_c\) Cake volume m³/s
\(\dot V_f\) Filtrate flow m³/s
\(TSS_f\) Filtrate solids kg/m³
\(\dot m_p\) Polymer kg/s

Method and standards

Mass balance.

Where it is used

  • Dewatering equipment selection.
  • Sludge disposal cost estimates.

Common mistakes

  • Leaving out filtrate recycle load.
  • Ignoring wash water on belt presses.

Assumptions and limits

  • Feed and filtrate densities are both taken as 1 000 kg/m³ (water); the cake bulk density is used only for the cake volume.

References

  • Metcalf & Eddy
  • Wastewater Engineering: Treatment and Resource Recovery
  • 5th ed. (McGraw-Hill, 2014)
  • ch. 14 (dewatering mass balances, solids capture)

Questions and answers

What is solids capture?

The share of feed solids that ends up in the cake; the rest returns to the plant in the filtrate.

Why does cake solids matter so much?

Going from 18 to 25 % solids cuts cake mass by almost 30 %, and with it haulage or drying cost.

What do the defaults give?

100 m³/d at 3 % to a 22 % cake with 95 % capture: 13 t/d of cake and about 15 kg/d of polymer.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.