FireCADCalc

Chemical Phosphorus Removal: Alum or Ferric Chloride Dose

Alum or ferric chloride needed to precipitate phosphorus from a molar metal-to-phosphorus ratio, as dry chemical and as a solution volume.

Sugar mill and cogenerationDistillery and ethanolRefinery and petrochemicalChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: Alum, 5 mg/L P, Al:P 2Ferric chloride 40 %, 3 mg/L P, Fe:P 1.8

Results

Molar ratios of 1.5–2.5 are typical to reach 0.5–1 mg/L total P; lower effluent targets need higher ratios. Jar tests set the dose. Alum solution is often 48 % at 1.33 kg/L; ferric chloride 40 % at 1.42 kg/L.

Metal dose (as Al or Fe)8.7112mg/L
Dry chemical959.51kg/d
Solution volume62.625L/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Alum, 5 mg/L P, Al:P 2. The inputs, in the units selected above:

InputValue
Flow10,000 m³/d
Phosphorus to remove5.0000 mg/L
ChemicalAlum Al₂(SO₄)₃·14H₂O
Molar metal-to-phosphorus ratio2.0000 -
Solution strength (mass fraction of the product named above: alum as the 14-hydrate, ferric chloride as FeCl₃)48.000 %
Solution density1,330.0 kg/m³

Applying the formula below gives:

ResultValue
Metal dose (as Al or Fe)8.7112 mg/L
Dry chemical959.51 kg/d
Solution volume62.625 L/h

Open this example in the calculator and change any input.

Formula

\(n_M = \frac{\Delta P}{30.974}\cdot(M{:}P), \quad C_M = n_M A_M, \quad \dot m = n_M\,\frac{M_{chem}}{\nu_M}\,Q, \quad \dot V = \frac{\dot m}{w\rho}\)

Variables

Symbol Meaning SI unit
\(Q\) Flow m³/s
\(\Delta P\) Phosphorus to remove kg/m³
\(\text{chemical}\) Chemical -
\(M:P\) Molar metal-to-phosphorus ratio -
\(w\) Solution strength (mass fraction) -
\(\rho\) Solution density kg/m³
\(C_M\) Metal dose (as Al or Fe) kg/m³
\(n_M\) Metal to add, molar kmol/m³
\(A_M\) Atomic mass of the metal kg/kmol
\(M_{chem}/\nu_M\) Product mass per kmol of metal kg/kmol
\(\dot m\) Dry chemical kg/s
\(\dot V\) Solution volume m³/s

Method and standards

Stoichiometry.

Where it is used

  • Effluent phosphorus limits.
  • Dairy and food wastewater.

Common mistakes

  • Using the mass ratio instead of the molar ratio.
  • Forgetting that alum carries two Al per molecule.

Assumptions and limits

  • Molar ratio from jar tests or practice.
  • n_M is the metal in kmol per m³; A_M is 26.982 kg/kmol for Al and 55.845 kg/kmol for Fe. M_chem/ν_M is the product mass per mole of metal: 594.4/2 kg/kmol for Al₂(SO₄)₃·14H₂O, 162.2 kg/kmol for FeCl₃.
  • Solution strength as the 14-hydrate for alum; a strength quoted as anhydrous Al₂(SO₄)₃ or as Al₂O₃ must be converted first.

References

  • Metcalf & Eddy
  • Wastewater Engineering: Treatment and Resource Recovery
  • 5th ed. (McGraw-Hill, 2014)
  • ch. 6 (chemical phosphorus removal, molar ratios)

Questions and answers

Why a molar ratio above 1?

Metal also forms hydroxides and reacts with alkalinity; extra metal is needed to drive phosphorus low.

Alum or ferric?

Both work; ferric also helps sulfide and odour control and sludge thickening, alum gives lighter-coloured sludge.

What do the defaults give?

5 mg/L P at Al:P 2 in 10,000 m³/d: 8.7 mg/L Al, 960 kg/d of alum, about 63 L/h of 48 % solution.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.