FireCADCalc

SCR Ammonia Dose and Slip

Ammonia for selective catalytic reduction (SCR) from the NOx load, the reduction and the allowed slip (NH₃ : NO ≈ 1 : 1), as anhydrous or aqueous ammonia.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationDistillery and ethanolBoilerStack and chimney

Inputs

Examples: 80 % reduction, 25 % aqueousAnhydrous

Results

Slip rises as the catalyst ages; ammonia with SO₃ forms ammonium bisulphate that fouls air heaters.

Ammonia (100 %)12.074kg/h
Reagent48.297kg/h
Molar ratio to inlet NOx0.81539

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 80 % reduction, 25 % aqueous. The inputs, in the units selected above:

InputValue
Flue gas flow (dry, normal)100,000 Nm³/h
NOx at the inlet (as NO₂, dry)400.00 mg/Nm³
NOx reduction wanted80.000 %
Ammonia slip (dry, by volume)3.0000 ppm
Ammonia strength of the reagent (1 for anhydrous)25.000 %

Applying the formula below gives:

ResultValue
Ammonia (100 %)12.074 kg/h
Reagent48.297 kg/h
Molar ratio to inlet NOx0.81539

Open this example in the calculator and change any input.

Formula

\(\dot n_{NH_3} = \eta\,\dot n_{NO_x} + \frac{\dot V_n y_{NH_3}}{V_m}, \quad \dot m_r = \frac{\dot n_{NH_3} M_{NH_3}}{w}\)

Variables

Symbol Meaning SI unit
\(\dot V_n\) Flue gas flow (dry, normal) Nm³/s
\(c_{NO_x}\) NOx at the inlet (as NO₂, dry) kg/m³
\(\eta\) NOx reduction wanted -
\(y_{NH_3}\) Ammonia slip (dry, by volume) -
\(w\) Ammonia strength of the reagent (1 for anhydrous) -
\(\dot m_{NH_3}\) Ammonia (100 %) kg/s
\(\dot m_r\) Reagent kg/s
\(NH_3/NO_x\) Molar ratio to inlet NOx -

Method and standards

Stoichiometry of the standard SCR reaction, one NH₃ per NOx molecule reduced (NOx counted as NO₂ for its mass), plus the slip at the outlet on the molar volume at 0 °C and 1 atm.

Where it is used

  • SCR reagent systems.
  • Operating cost estimates.

Common mistakes

  • Slip in mg/Nm³ entered as ppm.

Assumptions and limits

  • Dry, normal basis.
  • All NOx is treated as NO reacting 1 : 1. NO₂ (usually 5–10 % of boiler NOx) reacts by other routes and ammonia lost by oxidation on the catalyst is not counted; allow a margin on the dose from the catalyst maker.

References

  • Stoichiometry 4 NO + 4 NH₃ + O₂ → 4 N₂ + 6 H₂O (NH₃ : NO = 1); slip on the molar volume at 0 °C
  • 1 atm

Questions and answers

Why 1 : 1?

The standard SCR reaction consumes one NH₃ per NO.

NO₂ in the NOx?

Mostly NO in boiler flue gas; reporting as NO₂ is a convention for mass.

Aqueous or anhydrous?

25 % aqueous ammonia is easier to permit and store; anhydrous needs a smaller tank.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.