Worked example
Example: 3 m level difference, 2 m crest, 50 mm, K 6. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Level difference between the two surfaces | 3.0000 m |
| Height of the crest above the upper surface | 2.0000 m |
| Pipe inside diameter | 50.000 mm |
| Loss coefficient: entry, bends and friction f L/d, without the exit | 6.0000 - |
| Loss coefficient from the inlet to the crest | 2.0000 - |
| Liquid density | 998.00 kg/m³ |
| Vapour pressure of the liquid | 0.023390 bar |
| Atmospheric pressure | 1.0132 bar |
Applying the formula below gives:
| Result | Value |
|---|---|
| Velocity in the pipe | 2.8993 m/s |
| Flow | 20.494 m³/h |
| Absolute pressure at the crest | 0.69168 bar |
| Highest crest before the pressure reaches vapour pressure | 8.8283 m |
Open this example in the calculator and change any input.
Formula
\(v = \sqrt{\frac{2 g H}{1 + K_t}}, \quad p_c = p_a - \rho g z_c - (1 + K_c)\frac{\rho v^2}{2}\)
\(Q = v\frac{\pi d^2}{4}, \quad z_{max} = \frac{p_a - p_v - (1 + K_c)\rho v^2/2}{\rho g}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(H\) | Level difference between the two surfaces | m |
| \(z_c\) | Height of the crest above the upper surface | m |
| \(d\) | Pipe inside diameter | m |
| \(K_t\) | Loss coefficient: entry, bends and friction f L/d, without the exit | - |
| \(K_c\) | Loss coefficient from the inlet to the crest | - |
| \(\rho\) | Liquid density | kg/m³ |
| \(p_v\) | Vapour pressure of the liquid | Pa |
| \(p_a\) | Atmospheric pressure | Pa |
| \(v\) | Velocity in the pipe | m/s |
| \(Q\) | Flow | m³/s |
| \(p_c\) | Absolute pressure at the crest | Pa |
| \(z_{max}\) | Highest crest before the pressure reaches vapour pressure | m |
| \(g\) | Standard gravity, 9.806 65 | m/s² |
Method and standards
Bernoulli with losses.
Where it is used
- Draining tanks and pits.
- Cooling water and condensate siphons.
Common mistakes
- Ignoring vapour pressure.
- Counting the exit loss twice: it is the 1 in (1 + K_t), so K_t excludes it.
Assumptions and limits
- Steady, full-bore flow.
- K_t covers entry, bends and friction; the exit loss (one velocity head) is already in the formula as the 1.
- When the crest pressure would fall below the vapour pressure the siphon breaks: flow, velocity and crest pressure are not shown.
References
- Bernoulli with losses between the surfaces and to the crest (Textbook fluid mechanics (White, Fluid Mechanics))
Questions and answers
3 m level difference, 50 mm pipe, total K = 6?
Velocity 2.90 m/s, 20.5 m³/h.
How high can the crest be?
Below about 10 m for cold water, less with flow losses and warm water.
Why does warm water break a siphon?
Its vapour pressure is higher, so it boils at the crest sooner.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.