Worked example
Example: Sludge 10 Pa, 50 mPa s, DN100. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Yield stress | 10.000 Pa |
| Plastic viscosity | 50.000 cP |
| Density | 1,300.0 kg/m³ |
| Pipe inside diameter | 102.30 mm |
| Mean velocity | 1.5000 m/s |
| Pipe length | 100.00 m |
Applying the formula below gives:
| Result | Value |
|---|---|
| Bingham Reynolds number | 3,989.7 |
| Hedström number | 54,420 |
| Laminar Fanning friction factor | 0.012778 |
| Turbulent Fanning friction factor (Darby) | 0.006176 |
| Combined friction factor | 0.012778 |
| Pressure drop | 73.071 kPa |
Open this example in the calculator and change any input.
Formula
\(\frac{8V}{D} = \frac{\tau_w}{\mu_p}\left(1 - \frac43\xi + \frac13\xi^4\right), \ \xi = \frac{\tau_y}{\tau_w}, \quad f_L = \frac{2\tau_w}{\rho V^2}, \quad He = \frac{\rho D^2\tau_y}{\mu_p^2}\)
\(f_T = \frac{10^{a}}{Re_B^{0.193}}, \ a = -1.47\left[1 + 0.146e^{-2.9\times10^{-5}He}\right], \quad f = \left(f_L^m + f_T^m\right)^{1/m}, \ m = 1.7 + \frac{40000}{Re_B}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(\tau_y\) | Yield stress | Pa |
| \(\mu_p\) | Plastic viscosity | Pa·s |
| \(\rho\) | Density | kg/m³ |
| \(D\) | Pipe inside diameter | m |
| \(V\) | Mean velocity | m/s |
| \(L\) | Pipe length | m |
| \(Re_B\) | Bingham Reynolds number | - |
| \(He\) | Hedström number | - |
| \(f_L\) | Laminar Fanning friction factor | - |
| \(f_T\) | Turbulent Fanning friction factor (Darby) | - |
| \(f\) | Combined friction factor | - |
| \(\Delta p\) | Pressure drop | Pa |
Method and standards
Buckingham–Reiner laminar solution and Darby's combined correlation.
Where it is used
- Sludge, mud and paste lines.
- Ash slurry and lime slurry systems.
Common mistakes
- Using a power-law fit for a fluid with a clear yield stress.
- Ignoring the start-up pressure to break the yield stress.
Assumptions and limits
- Bingham model; smooth pipes only (Darby's turbulent correlation has no roughness term).
- The laminar–turbulent transition Reynolds number, which rises with He, is not reported; the combined factor bridges the two regimes.
References
- Perry's Chemical Engineers' Handbook
- 9th ed. (McGraw-Hill, 2019)
- sec. 6
- Eqs. (6-66) and (6-67) and Table 6-9 (Bingham plastics, Hedström number)
- Buckingham–Reiner laminar solution; Darby
- Mun and Boger (1992)
- Chem. Eng. 99(9): 116 (turbulent and combined friction factor)
Questions and answers
What is a Bingham plastic?
A material that does not flow until the shear stress exceeds a yield stress, then flows with a constant plastic viscosity: toothpaste, drilling mud, sewage sludge, concentrated slurries.
What does the Hedström number tell me?
How strong the yield stress is relative to viscous forces; it raises the critical Reynolds number for turbulence.
Why is the laminar friction factor so high?
Part of the pipe cross-section moves as an unsheared plug, so more pressure is needed to shear the rest.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.