FireCADCalc

Gas Turbine Inlet Evaporative Cooling: Power Gain and Water

Compressor inlet temperature after an evaporative cooler or fogger from dry bulb, humidity and effectiveness, with the output gain and water used.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationDistillery and ethanolRefinery and petrochemicalChemical and fertiliserIAPWS-IF97 (water and steam)

Inputs

Examples: 40 °C, 30 %, 90 % effective, 40 MWFogging at 35 °C, 50 %

Results

Wet bulb from the psychrometric relation (ASHRAE Fundamentals) with saturation from IAPWS-IF97; the cooling follows the wet-bulb line. Take the output sensitivity from the gas turbine maker's ambient correction curve (typically 0.5–0.8 %/K).

Wet bulb temperature26.141°C
Compressor inlet temperature26.141°C
Inlet cooling8.8592K
Output gain9.3021MW
Water evaporated6.1111t/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 40 °C, 30 %, 90 % effective, 40 MW. The inputs, in the units selected above:

InputValue
Ambient dry bulb40.000 °C
Relative humidity30.000 %
Ambient pressure101.33 kPa
Cooler effectiveness (fogging ≈ 1)90.000 %
Compressor air flow (dry air)540,000 kg/h
Gas turbine output at ambient40.000 MW
Output gain per K of inlet cooling (%/K)0.60000 -

Applying the formula below gives:

ResultValue
Wet bulb temperature25.093 °C
Compressor inlet temperature26.583 °C
Inlet cooling13.417 K
Output gain3.2200 MW
Water evaporated3.0571 t/h

Open this example in the calculator and change any input.

Formula

\(T_2 = T_{db} - \varepsilon(T_{db} - T_{wb}), \quad \Delta P = \frac{s}{100}P_0(T_{db} - T_2), \quad \dot m_w = \dot m_a(W_2 - W_1)\)

Variables

Symbol Meaning SI unit
\(T_{db}\) Ambient dry bulb K
\(\phi\) Relative humidity -
\(p\) Ambient pressure Pa
\(\varepsilon\) Cooler effectiveness (fogging ≈ 1) -
\(\dot m_a\) Compressor air flow kg/s
\(P_0\) Gas turbine output at ambient W
\(s\) Output gain per K of inlet cooling (%/K) -
\(T_{wb}\) Wet bulb temperature K
\(T_2\) Compressor inlet temperature K
\(\Delta T\) Inlet cooling K
\(\Delta P\) Output gain W
\(\dot m_w\) Water evaporated kg/s

Method and standards

Psychrometrics with the maker's sensitivity.

Where it is used

  • Peak-season output enhancement.
  • Water budget for coolers and foggers.

Common mistakes

  • Using dry-bulb sensitivity for a different gas turbine.
  • Forgetting water quality for foggers.

Assumptions and limits

  • Adiabatic cooling along the wet-bulb line; s is entered in %/K, hence the division by 100.
  • The air flow is taken as dry air in the water balance; using the moist-air flow instead changes the water by 1–3 % in hot humid weather.
  • Air whose wet bulb is below 0 °C is rejected: the method assumes liquid water.

References

  • Psychrometric wet-bulb relation (ASHRAE Handbook — Fundamentals, ch. 1) with IAPWS-IF97 saturation; output from the maker's correction factor

Questions and answers

Why does cooling the inlet raise output?

Colder air is denser, so the compressor passes more mass; output falls roughly 0.5–0.8 % per K of ambient rise.

When does it work best?

In hot, dry weather, when the wet-bulb depression is large.

What do the defaults give?

40 °C at 30 % RH (wet bulb about 25 °C), 90 % effectiveness: about 13 K of cooling, roughly 3.2 MW more on a 40 MW unit, using about 3 t/h of water.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.