Worked example
Example: 10 bar(a) 250 °C to 2 bar(a), 95 %, 1 kg/s. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Inlet pressure (absolute) | 10.000 bar |
| Inlet steam | Superheated at the temperature below |
| Inlet temperature (superheated) | 250.00 °C |
| Exit pressure (absolute) | 2.0000 bar |
| Nozzle efficiency | 95.000 % |
| Approach velocity | 0 m/s |
| Steam flow | 3,600.0 kg/h |
Applying the formula below gives:
| Result | Value |
|---|---|
| Isentropic enthalpy drop to the exit | 315.75 kJ/kg |
| Actual enthalpy drop η Δh_s | 299.96 kJ/kg |
| Exit velocity √(2 Δh + V₁²) | 774.54 m/s |
| Critical (throat) pressure | 5.4468 bar |
| Critical pressure ratio | 0.54468 |
| Throat velocity | 513.59 m/s |
| Throat area for the flow | 722.35 mm² |
| Exit area for the flow | 1,110.9 mm² |
| Dryness at the exit (1 when superheated) | 97.139 % |
Open this example in the calculator and change any input.
Formula
\(V_2 = \sqrt{2\, \eta_n\, \Delta h_s + V_1^2} = 44.72 \sqrt{\eta_n\, \Delta h_s\ [\text{kJ/kg}]}\ (V_1 = 0)\)
\(G = \rho \sqrt{2 (h_0 - h)}\ \text{on}\ s = s_1, \quad p_c: G = G_{max}\)
\(A_t = \frac{\dot m\, v_t}{V_t}, \quad A_2 = \frac{\dot m\, v_2}{V_2}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(p_1\) | Inlet pressure (absolute) | Pa |
| \(\text{inlet}\) | Inlet steam | - |
| \(T_1\) | Inlet temperature (superheated) | K |
| \(p_2\) | Exit pressure (absolute) | Pa |
| \(\eta_n\) | Nozzle efficiency | - |
| \(V_1\) | Approach velocity | m/s |
| \(\dot m\) | Steam flow | kg/s |
| \(\Delta h_s\) | Isentropic enthalpy drop to the exit | J/kg |
| \(\Delta h\) | Actual enthalpy drop η Δh_s | J/kg |
| \(V_2\) | Exit velocity √(2 Δh + V₁²) | m/s |
| \(p_c\) | Critical (throat) pressure | Pa |
| \(p_c/p_1\) | Critical pressure ratio | - |
| \(V_t\) | Throat velocity | m/s |
| \(A_t\) | Throat area for the flow | m² |
| \(A_2\) | Exit area for the flow | m² |
| \(x_2\) | Dryness at the exit (1 when superheated) | - |
Method and standards
Steady adiabatic flow: kinetic energy gained equals enthalpy lost. The critical (choked) pressure is where the mass flux on the IF97 isentrope is greatest.
Worked example
Steam at 10 bar absolute and 250 °C expands in a nozzle to 2 bar absolute; nozzle efficiency 95 %.
- h₁ = 2943 kJ/kg; isentropic h₂ = 2627 kJ/kg; drop 315.7 kJ/kg
- Actual drop = 0.95 × 315.7 = 300.0 kJ/kg
- V₂ = 44.72 × √300.0 = 774.5 m/s
- Critical pressure = 0.545 × 10 = 5.45 bar: 2 bar is lower, so the nozzle is convergent–divergent
Where it is used
- Boiler operator and engineer examinations.
- Steam turbine and ejector nozzles.
- Safety valve and orifice flow understanding.
Common mistakes
- Forgetting the 2 and the kJ to J (44.72 comes from √2000).
- Using the exit pressure as the throat pressure.
- Applying the efficiency to the velocity instead of the enthalpy drop.
Assumptions and limits
- Equilibrium expansion; supersaturation not modelled.
- Nozzle efficiency applied to the whole drop. For a convergent nozzle (exit above the critical pressure) the throat is the exit, so the throat values equal the exit values at the actual state.
- With an approach velocity the flux uses the stagnation enthalpy h₀, while the critical pressure ratio is referred to the static inlet pressure, not the stagnation pressure used in some textbooks.
- The critical pressure is searched between 0.2 and 0.999 p₁; a result at the edge is flagged.
References
- IAPWS-IF97 (water and steam)
- Isentropic nozzle flow (textbook)
Questions and answers
What exit velocity does steam at 10 bar(a), 250 °C reach expanding to 2 bar(a) at 95 % efficiency?
The isentropic drop is 315.7 kJ/kg, the actual 300.0 kJ/kg, so V₂ = √(2 × 300 000) = 774.5 m/s (44.72 √(Δh in kJ/kg)).
What is the critical pressure ratio?
Found on the steam's own isentrope: 0.545 for this superheated steam and 0.577 for dry saturated steam, matching the textbook 0.546 and 0.577.
When is a divergent part needed?
When the exit pressure is below the critical pressure; otherwise a convergent nozzle is enough.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.