FireCADCalc

Steam Turbine Isentropic Efficiency

Isentropic (internal) efficiency of a steam turbine from measured inlet and exhaust pressures and temperatures, with the actual and isentropic enthalpy drops (IAPWS-IF97).

Thermal power plantSugar mill and cogenerationPulp and paperIAPWS-IF97 (water and steam)Steam turbineBoiler operation engineer (BOE) examinations

Inputs

Examples: 45 bar(a) / 400 °C to 4 bar(a), exhaust 200 °C66 bar(a) / 485 °C to 12 bar(a), exhaust 300 °C105 bar(a) / 535 °C to 18 bar(a), exhaust 320 °C

Results

Isentropic efficiency63.099%
Actual enthalpy drop344.57kJ/kg
Isentropic enthalpy drop546.07kJ/kg
Exhaust enthalpy2,861.0kJ/kg
Isentropic exhaust enthalpy2,659.5kJ/kg

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 45 bar(a) / 400 °C to 4 bar(a), exhaust 200 °C. The inputs, in the units selected above:

InputValue
Inlet steam pressure (absolute)45.000 bar
Inlet steam conditionSuperheated at the temperature below
Inlet steam temperature (superheated only)400.00 °C
Exhaust pressure (absolute)400.00 kPa
Measured exhaust temperature (superheated exhaust)200.00 °C

Applying the formula below gives:

ResultValue
Isentropic efficiency63.099 %
Actual enthalpy drop344.57 kJ/kg
Isentropic enthalpy drop546.07 kJ/kg
Exhaust enthalpy2,861.0 kJ/kg
Isentropic exhaust enthalpy2,659.5 kJ/kg

Open this example in the calculator and change any input.

Formula

\(\eta_i = \frac{h_1 - h_2}{h_1 - h_{2s}} \qquad h_{2s} = h(p_2, s_1) \qquad h_2 = h(p_2, T_2)\)

Variables

Symbol Meaning SI unit
\(p_1\) inlet pressure, absolute Pa
\(\text{state}\) dry saturated or superheated inlet –
\(T_1\) inlet temperature (superheated) K
\(p_2\) exhaust pressure, absolute Pa
\(T_2\) measured exhaust temperature K
\(\eta_i\) isentropic efficiency –
\(h_1 - h_2\) actual enthalpy drop J/kg
\(h_1 - h_{2s}\) isentropic enthalpy drop J/kg
\(h_2\) exhaust enthalpy J/kg
\(h_{2s}\) isentropic exhaust enthalpy J/kg
\(s_1\) inlet entropy J/(kg·K)

Method and standards

Isentropic efficiency as the ratio of actual to isentropic enthalpy drop, the enthalpy-drop method used in turbine performance testing (ASME PTC 6 uses the same idea for its sections). Enthalpies and entropies from FireCAD's IAPWS-IF97.

Where it is used

  • Routine performance monitoring of back-pressure and extraction turbines.
  • Before and after an overhaul, to see what the repair gained.
  • Checking a vendor's efficiency claim at site conditions.

Common mistakes

  • Using an exhaust temperature measured too close to a desuperheater or drain.
  • Ignoring the pressure drop across stop and control valves when the inlet is measured upstream of them.
  • Applying it to wet exhaust.

Assumptions and limits

  • Exhaust superheated (vapour) for a measured temperature to fix its state; supercritical exhaust is not accepted (not reached at exhaust pressures in practice); steady flow; heat loss from the casing neglected.
  • An efficiency outside 0–100 % is rejected as a reading error.

References

  • IAPWS R7-97(2012) IF97
  • ASME PTC 6 (enthalpy-drop efficiency concept)

Questions and answers

How do I find a turbine's efficiency from plant readings?

Compare the actual enthalpy drop with the isentropic one. Steam at 45 bar(a) and 400 °C leaving at 4 bar(a) and 200 °C dropped 345 kJ/kg, against 546 kJ/kg isentropically: 63.1 % efficient.

Why can't I use it on a condensing turbine?

Its exhaust is wet, and temperature alone does not tell the dryness. For condensing turbines measure the efficiency of the superheated sections, or find the exhaust enthalpy from a condenser heat balance.

What does falling efficiency tell me?

Deposits on the blades, worn seals or damaged nozzles. Track it at the same load and pressures; a drop of a few points is worth an inspection.

Method and article reviewed by FireCAD engineering on 11 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.