Worked example
Example: 20 t/h, 45 bar(a) / 400 °C reduced to 4 bar(a). The inputs, in the units selected above:
| Input | Value |
|---|---|
| Steam flow through the PRDS | 20,000 kg/h |
| Inlet steam pressure (absolute) | 45.000 bar |
| Inlet steam condition | Superheated at the temperature below |
| Inlet steam temperature (superheated only) | 400.00 °C |
| Process (reduced) pressure (absolute) | 400.00 kPa |
| Turbine isentropic efficiency | 70.000 % |
| Gearbox and generator efficiency | 94.000 % |
| Operating hours per year | 8,000.0 h |
| Value of electricity per kWh (your currency) | 8.0000 - |
Applying the formula below gives:
| Result | Value |
|---|---|
| Electrical power a turbine would make | 1,996.2 kW |
| Value of that power per year (your currency) | 1.2776e+08 |
| Steam temperature after the PRDS valve (before spray) | 367.17 °C |
| Steam temperature after the turbine | 182.18 °C |
| Turbine exhaust dryness (1 = dry or superheated) | 100.00 % |
| Turbine exhaust enthalpy | 2,823.3 kJ/kg |
Open this example in the calculator and change any input.
Formula
\(h_2 = h_1 - \eta_i\,\left[h_1 - h(p_2, s_1)\right] \qquad P_{el} = \eta_g\,\dot m_s\,(h_1 - h_2)\)
\(V = P_{el}\,t_{op}\,c_e \qquad T_{PRDS} = T(p_2, h_1)\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(\dot m_s\) | steam flow through the PRDS | kg/s |
| \(p_1\) | supply pressure, absolute | Pa |
| \(\text{state}\) | dry saturated or superheated supply | – |
| \(T_1\) | supply temperature (superheated) | K |
| \(p_2\) | process (reduced) pressure, absolute | Pa |
| \(\eta_i\) | turbine isentropic efficiency | – |
| \(\eta_g\) | gearbox and generator efficiency | – |
| \(t_{op}\) | operating hours per year | s |
| \(c_e\) | value of electricity per kWh | – |
| \(P_{el}\) | electrical power a turbine would make | W |
| \(V\) | value of that power per year | – |
| \(T_{PRDS}\) | steam temperature after the valve, before spray | K |
| \(T_2\) | steam temperature after the turbine | K |
| \(x_2\) | turbine exhaust dryness | – |
| \(h_2\) | turbine exhaust enthalpy | J/kg |
| \(h_1\), \(s_1\) | supply enthalpy and entropy | J/kg, J/(kg·K) |
Method and standards
The PRDS valve is isenthalpic (throttling); the turbine follows the isentropic-efficiency expansion. States by FireCAD's IAPWS-IF97. Energy in kWh for the value.
Where it is used
- Screening letdown turbines and micro steam turbines for process plants.
- Energy audits: showing the cost of reducing high-pressure steam through valves.
- Cogeneration feasibility before asking turbine makers for offers.
Common mistakes
- Counting full-load flow for all hours when the PRDS flow varies.
- Forgetting that the process still needs the same heat: the boiler must make a little more steam.
- Using a large-turbine efficiency for a small single-stage machine.
Assumptions and limits
- Same steam flow through the turbine as through the PRDS; constant efficiencies; desuperheating not modelled.
- The extra boiler steam needed to give the process the same heat is not computed; the note gives the enthalpy deficit per kg.
- x₂ follows the property library: 1 for dry or superheated exhaust.
References
- IAPWS R7-97(2012) IF97
- first law of thermodynamics
Questions and answers
How much power is lost in a PRDS?
As much as a back-pressure turbine would make from the same steam. 20 t/h reduced from 45 bar(a) and 400 °C to 4 bar(a) could give about 2.0 MW with a 70 % efficient turbine and 94 % generator efficiency (the page default of 95 % gives about 2.02 MW), worth about 128 million a year at 8 per kWh over 8000 hours.
Does the process lose heat if a turbine replaces the PRDS?
A little: the power taken out comes from the steam's enthalpy, so the exhaust carries less heat per kg. The boiler supplies that extra heat, at boiler efficiency, which is still far cheaper than grid power in most plants.
Why is the PRDS steam so hot?
Throttling keeps the enthalpy, so steam from 45 bar(a) and 400 °C leaves the valve at about 367 °C at 4 bar(a); the spray water brings it down. A turbine exhaust is much cooler, about 182 °C here.
Method and article reviewed by FireCAD engineering on 11 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.