Worked example
Example: 550,000 lb/h exhaust at 14 % O2, 30 MW. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Exhaust gas flow | 249.48 t/h |
| Oxygen in the exhaust (by volume, wet basis) | 14.000 % |
| Exhaust molar mass | 29.500 kg/kmol |
| Fuel (Ganapathy Table 2.4: dry air per MMBtu fired, lb) | Natural gas (730) |
| Fuel LHV/HHV ratio | 90.000 % |
| Planned firing (LHV) | 30.000 MW |
| Exhaust specific heat | 1.1300 kJ/(kg·K) |
Applying the formula below gives:
| Result | Value |
|---|---|
| Equivalent air in the exhaust | 164.72 t/h |
| Maximum heat that can be fired (LHV) | 131.21 MW |
| Planned firing as a share of the maximum | 22.863 % |
| Gas temperature rise from the planned firing | 383.10 K |
Open this example in the calculator and change any input.
Formula
\(W_a = \frac{W_g\,O \times 32}{0.23\,M_g}, \quad Q_{max} = W_a\,\frac{LHV}{A\,HHV}, \quad \Delta T = \frac{Q}{W_g c_{pg}}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(W_g\) | Exhaust gas flow | kg/s |
| \(O\) | Oxygen in the exhaust (by volume, wet basis) | - |
| \(M_g\) | Exhaust molar mass | kg/kmol |
| \(A\) | Fuel (Ganapathy Table 2.4: dry air per MMBtu fired, lb) | - |
| \(LHV/HHV\) | Fuel LHV/HHV ratio | - |
| \(Q\) | Planned firing (LHV) | W |
| \(c_{pg}\) | Exhaust specific heat | J/(kg·K) |
| \(W_a\) | Equivalent air in the exhaust | kg/s |
| \(Q_{max}\) | Maximum heat that can be fired (LHV) | W |
| \(Q/Q_{max}\) | Planned firing as a share of the maximum | - |
| \(\Delta T\) | Gas temperature rise from the planned firing | K |
Method and standards
Ganapathy's oxygen balance; LHV/(A·HHV) ≈ 0.00124 for gas and oil.
Where it is used
- HRSG duct burner sizing.
- Checking supplementary firing schemes.
Common mistakes
- Firing to zero oxygen.
- Using HHV heat input with LHV limits.
Assumptions and limits
- Exhaust oxygen known; complete combustion.
- Exhaust oxygen must be above zero; a planned firing above the maximum is flagged, and its temperature rise then cannot be reached.
- The oxygen is by volume on the wet exhaust, consistent with the wet molar mass M_g in the volume-to-mass conversion.
- Table 2.4 figures are lb of air per MMBtu; the page converts them to SI.
References
- Ganapathy
- Steam Plant Calculations Manual
- 2nd ed. (Marcel Dekker, 1993)
- Q2.27
- Eqs. (22)–(25)
- and Table 2.4
Questions and answers
Why can gas turbine exhaust be fired?
It holds 14–16 % oxygen, enough to burn fuel without fresh air.
How far can it go?
In theory until the oxygen is used; burners need a few per cent left, so firing to about 2,000 °F is a practical limit.
What is 0.23?
The mass fraction of oxygen in air.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.