FireCADCalc

Feedwater Heater: TTD, DCA and Temperature Rise

Terminal temperature difference, drain cooler approach and temperature rise of a feedwater heater from shell pressure and water and drain temperatures.

Thermal power plantSugar mill and cogenerationPulp and paperIAPWS-IF97 (water and steam)Boiler operation engineer (BOE) examinations

Inputs

Examples: HP heater 12 bar(a)LP heater 1.5 bar(a)

Results

A rising TTD or DCA over time points to fouling, air blanketing or a high drain level.

Saturation temperature at shell pressure111.35°C
Terminal temperature difference T_sat − T_fw,out4.3500K
Drain cooler approach T_d − T_fw,in8.0000K
Feedwater temperature rise62.000K

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: HP heater 12 bar(a). The inputs, in the units selected above:

InputValue
Shell (extraction steam) pressure (absolute)12.000 bar
Feedwater in140.00 °C
Feedwater out185.00 °C
Drain leaving148.00 °C

Applying the formula below gives:

ResultValue
Saturation temperature at shell pressure187.96 °C
Terminal temperature difference T_sat − T_fw,out2.9646 K
Drain cooler approach T_d − T_fw,in8.0000 K
Feedwater temperature rise45.000 K

Open this example in the calculator and change any input.

Formula

\(TTD = T_{sat}(p_s) - T_{fw,out}, \quad DCA = T_d - T_{fw,in}\)

Variables

Symbol Meaning SI unit
\(p_s\) Shell (extraction steam) pressure (absolute) Pa
\(T_{fw,in}\) Feedwater in K
\(T_{fw,out}\) Feedwater out K
\(T_d\) Drain leaving K
\(T_{sat}\) Saturation temperature at shell pressure K
\(TTD\) Terminal temperature difference T_sat − T_fw,out K
\(DCA\) Drain cooler approach T_d − T_fw,in K
\(\Delta T\) Feedwater temperature rise K

Method and standards

Definitions.

Where it is used

  • Heater performance monitoring.
  • BOE examinations.

Common mistakes

  • Gauge pressure for T_sat.
  • Confusing TTD and DCA.

Assumptions and limits

  • Steady operation.
  • A negative TTD is possible with a desuperheating zone. A negative DCA, or a drain hotter than saturation, is not physical; notes flag both.

References

  • TTD = T_sat(p_shell) − T_fw
  • out; DCA = T_drain − T_fw
  • in (definitions as in the HEI Standards for Closed Feedwater Heaters and ASME PTC 12.1, Closed Feedwater Heaters); T_sat from IAPWS-IF97

Questions and answers

12 bar(a) shell, feedwater 140 → 185 °C, drain 148 °C?

T_sat about 188 °C: TTD about 3 K, DCA 8 K, rise 45 K.

Negative TTD?

Possible with a desuperheating zone: the outlet can exceed T_sat.

High DCA?

Often a low drain level letting steam through the drain cooler.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.