FireCADCalc

Weibull Failure Probability of a Brittle Material

Failure probability of a brittle part from Weibull characteristic strength and modulus with a size effect, and the stress for a target probability.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationRefinery and petrochemicalChemical and fertiliserPulp and paper

Inputs

Examples: 250 MPa on a 300 MPa, m 10 ceramicPart 50× the test volume, m 8

Results

Weibull weakest-link statistics; larger parts are weaker because they contain more flaws. Modulus 5–15 for ceramics, 20 or more for good engineering ceramics.

Failure probability at σ14.914%
Stress for the target probability189.38MPa

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 250 MPa on a 300 MPa, m 10 ceramic. The inputs, in the units selected above:

InputValue
Applied stress250.00 MPa
Characteristic strength (63.2 %) of the test volume300.00 MPa
Weibull modulus10.000 -
Stressed volume relative to the test volume1.0000 -
Target failure probability1.0000 %

Applying the formula below gives:

ResultValue
Failure probability at σ14.914 %
Stress for the target probability189.38 MPa

Open this example in the calculator and change any input.

Formula

\(P_f = 1 - \exp\left[-\frac{V}{V_0}\left(\frac{\sigma}{\sigma_0}\right)^m\right], \quad \sigma_t = \sigma_0\left[\frac{-\ln(1 - P_t)}{V/V_0}\right]^{1/m}\)

Variables

Symbol Meaning SI unit
\(\sigma\) Applied stress Pa
\(\sigma_0\) Characteristic strength (63.2 %) of the test volume Pa
\(m\) Weibull modulus -
\(V/V_0\) Stressed volume relative to the test volume -
\(P_t\) Target failure probability -
\(P_f\) Failure probability at σ -
\(\sigma_t\) Stress for the target probability Pa

Method and standards

Weibull distribution.

Where it is used

  • Ceramic components and refractories.
  • Glass and brittle coatings.

Common mistakes

  • Using a test-bar σ₀ for a large part without the size effect.
  • Fitting m from too few tests.

Assumptions and limits

  • Uniform stress; volume flaws. σ₀ from flexural tests belongs to the effective (stressed) volume of the test bar, which is much smaller than its geometric volume; using geometric volumes for a tensile part understates the size effect. Use effective volumes in V/V₀.

References

  • Weibull (1951) weakest-link distribution P_f = 1 − exp[−(V/V₀)(σ/σ₀)^m] (Dowling, Mechanical Behavior of Materials, 4th ed. (Pearson, 2013), ch. 8)

Questions and answers

What does the modulus m mean?

How scattered the strength is: high m means consistent strength, low m means wide scatter and a large size effect.

Why does part size matter?

A bigger stressed volume is more likely to contain a large flaw, so its median strength is lower.

What do the defaults represent?

A ceramic with 300 MPa characteristic strength and modulus 10, loaded to 250 MPa.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.