FireCADCalc

Slurry Stream: Percent Solids, Solids Rate and Conditioner Volume

Percent solids, dry solids and water rates, solids by volume and dilution ratio of a slurry stream from flow and pulp density, and conditioner volume.

Inputs

Examples: Wills Example 3.4: 1 L can filled in 7 s, quartz pulp at 1,400 kg/m3Wills Example 3.6: flotation feed 935.2 m3/h at 40 % solidsMill discharge, magnetite ore

Results

The tank volume is the slurry volume for the nominal retention time; add freeboard and allow for air in aerated or agitated tanks. Measure pulp density on a sample free of air bubbles.

Solids by mass62.637%
Dry solids rate549.64t/h
Water rate327.86t/h
Solids by volume27.143%
Dilution ratio (water : solids)0.59649
Conditioning tank volume15.000m³

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Wills Example 3.4: 1 L can filled in 7 s, quartz pulp at 1,400 kg/m3. The inputs, in the units selected above:

InputValue
Slurry volume flow0.51429 m³/h
Pulp density1,400.0 kg/m³
Density of the dry solids2,650.0 kg/m³
Density of the water1,000.0 kg/m³
Retention time in a conditioning tank5.0000 min

Applying the formula below gives:

ResultValue
Solids by mass45.887 %
Dry solids rate0.33039 t/h
Water rate0.38961 t/h
Solids by volume24.242 %
Dilution ratio (water : solids)1.1792
Conditioning tank volume0.042857 m³

Open this example in the calculator and change any input.

Formula

\(x = \frac{\rho_s(D - \rho_w)}{D(\rho_s - \rho_w)}, \quad M = F D x, \quad x_v = \frac{x D}{\rho_s}, \quad DR = \frac{1 - x}{x}, \quad V = F t_r\)

Variables

Symbol Meaning SI unit
\(F\) Slurry volume flow m³/s
\(D\) Pulp density kg/m³
\(\rho_s\) Density of the dry solids kg/m³
\(\rho_w\) Density of the water kg/m³
\(t_r\) Retention time in a conditioning tank s
\(x\) Solids by mass -
\(M\) Dry solids rate kg/s
\(M_w\) Water rate kg/s
\(x_v\) Solids by volume -
\(DR\) Dilution ratio (water : solids) -
\(V\) Conditioning tank volume m³

Method and standards

Pulp density relations.

Where it is used

  • Plant mass balances and surveys.
  • Sizing conditioners, sumps and agitators.

Common mistakes

  • Using the pulp density of an aerated sample.
  • Mixing mass and volume percent solids.

Assumptions and limits

  • Water and solids incompressible; no air.

References

  • Wills and Finch
  • Wills' Mineral Processing Technology
  • 8th ed. (Butterworth-Heinemann, 2016)
  • ch. 3
  • eqs. 3.12-3.17
  • Examples 3.4 and 3.6

Questions and answers

Why the dilution ratio?

Multiplied by the solids rate it gives the water rate directly, which is how water balances around a plant are built.

How is the solids density found?

With a density bottle on a dried sample (Wills's 12-step method), or from the mineralogy.

What do the defaults represent?

Wills's Example 3.4: a 1 L can filled in 7 s with quartz pulp of 1,400 kg/m³ (45.9 % solids, 330 kg/h of quartz), with a 5-minute conditioner.

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.