FireCADCalc

Drop-Weight Breakage: t10 from Specific Energy (A and b)

Breakage index t10 for a specific comminution energy from the JK drop-weight parameters A and b, the hardness index A × b, and the energy for a target t10.

Inputs

Examples: Medium ore, A 65, b 0.85, 1 kWh/tHard ore, A x b 30Soft ore, A x b 120

Results

t10 is the percentage passing one tenth of the original particle size after breakage. A high A × b means an ore that breaks easily (low work index).

Breakage index t10 at E_cs37.218%
Hardness index A × b55.250
Energy for the target t100.43262kWh/t

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Medium ore, A 65, b 0.85, 1 kWh/t. The inputs, in the units selected above:

InputValue
Maximum t10 (parameter A)65.000 %
Parameter b0.85000 t/kWh
Specific comminution energy1.0000 kWh/t
Target t1020.000 %

Applying the formula below gives:

ResultValue
Breakage index t10 at E_cs37.218 %
Hardness index A × b55.250
Energy for the target t100.43262 kWh/t

Open this example in the calculator and change any input.

Formula

\(t_{10} = A\left(1 - e^{-b E_{cs}}\right), \quad E_{cs} = -\frac{1}{b}\ln\left(1 - \frac{t_{10}}{A}\right)\)

Variables

Symbol Meaning SI unit
\(A\) Maximum t10 (parameter A) -
\(b\) Parameter b kg/J
\(E_{cs}\) Specific comminution energy J/kg
\(t_{10}^*\) Target t10 -
\(t_{10}\) Breakage index t10 at E_cs -
\(A\times b\) Hardness index A × b -
\(E_{cs}^*\) Energy for the target t10 J/kg

Method and standards

JK breakage function.

Where it is used

  • Ore characterisation for SAG and crusher models.
  • Comparing hardness of ore domains.

Common mistakes

  • Entering A as a fraction in the A × b product.
  • Mixing b in t/kWh with energy in J/kg.

Assumptions and limits

  • Single-particle impact breakage.

References

  • Wills and Finch
  • Wills' Mineral Processing Technology
  • 8th ed. (Butterworth-Heinemann, 2016)
  • ch. 5
  • eq. 5.9 (Napier-Munn et al., 1996)

Questions and answers

What do A and b mean?

A is the largest t10 the ore can reach however hard it is hit; b sets how fast t10 rises with energy. Their product ranks ore hardness.

How is the test done?

Single-size rocks are broken at three energies each in a drop-weight tester and the products sized (over 60 kg of rock; the SMC Test needs less).

What do the defaults represent?

A medium ore with A = 65 % and b = 0.85 t/kWh (A × b = 55) broken at 1 kWh/t, and the energy for t10 = 20 %.

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.