FireCADCalc

Tumbling Mill Critical Speed and Operating Speed

Critical speed of a ball, rod or SAG mill from its diameter and the ball size, the operating speed at a fraction of critical, shell speed and charge release angle.

Inputs

Examples: Ball mill 4.12 m, 64 mm balls, 71.7 % of critical (Wills Table ex 7.2)SAG mill 12.2 m, 125 mm balls, 75 %Laboratory mill 0.305 m, 25 mm balls, 70 %

Results

Mills run at 50–90 % of critical: rod mills about 60–70 %, ball mills 70–80 % (Wills). The release angle is for the outer layer with no slip; lifters and slip change the real trajectory.

Critical speed20.999rpm
Operating speed15.056rpm
Angle of release of the outer balls from the vertical59.063°
Shell peripheral speed3.2480m/s

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Ball mill 4.12 m, 64 mm balls, 71.7 % of critical (Wills Table ex 7.2). The inputs, in the units selected above:

InputValue
Mill diameter inside the liners4.1200 m
Largest ball or rod diameter64.000 mm
Operating speed as a fraction of critical71.700 %

Applying the formula below gives:

ResultValue
Critical speed20.999 rpm
Operating speed15.056 rpm
Angle of release of the outer balls from the vertical59.063 °
Shell peripheral speed3.2480 m/s

Open this example in the calculator and change any input.

Formula

\(N_c = \frac{42.3}{\sqrt{D - d}}\ \text{rpm}, \quad \cos\alpha = \frac{(2\pi N/60)^2 (D - d)/2}{g}\)

Variables

Symbol Meaning SI unit
\(D\) Mill diameter inside the liners m
\(d\) Largest ball or rod diameter m
\(N/N_c\) Operating speed as a fraction of critical -
\(N_c\) Critical speed 1/s
\(N\) Operating speed 1/s
\(\alpha\) Angle of release of the outer balls from the vertical rad
\(v\) Shell peripheral speed m/s

Method and standards

Balance of weight and centrifugal force on the outer ball.

Where it is used

  • Setting mill speed and variable-speed drives.
  • Checking liner and lifter design.

Common mistakes

  • Using the shell diameter instead of inside the liners.
  • Confusing rpm with fraction of critical.

Assumptions and limits

  • No slip at the liner.

References

  • Wills and Finch
  • Wills' Mineral Processing Technology
  • 8th ed. (Butterworth-Heinemann, 2016)
  • ch. 7
  • eqs. 7.1-7.4
  • Perry's Chemical Engineers' Handbook
  • 9th ed.
  • sec. 21
  • eq. 21-143

Questions and answers

What happens at critical speed?

The outer layer of balls is held against the shell all the way round and no longer falls, so grinding stops.

Why include the ball size?

The ball centre runs at radius (D − d)/2; for large mills the correction is small.

What do the defaults represent?

The 4.12 m ball mill of Wills's Table ex 7.2 with 64 mm balls at 71.7 % of critical.

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.