FireCADCalc

Ball Mill Power by Bond's Equation and Operating Work Index

Specific energy and power of a rod or ball mill by Bond's equation with Rowland's efficiency factors, and the operating work index from measured power.

Inputs

Examples: Wills Example 7.2: ball mill in closed circuit with cyclonesCopper ore regrind, EF 1.15Rod mill, coarse feed

Results

Bond's equation applies to ball and rod milling of 'normal' feeds; Rowland's factors correct for dry grinding, open circuit, mill diameter, oversize feed, fine grinding and reduction ratio. Select the mill from a calibrated power model or the maker's tables.

Specific energy5.7248kWh/t
Mill power required858.71kW
Operating work index from measured power11.005kWh/t
Circuit efficiency (laboratory over operating index)95.413%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Wills Example 7.2: ball mill in closed circuit with cyclones. The inputs, in the units selected above:

InputValue
Feed 80 % passing size600.00 µm
Product 80 % passing size110.00 µm
Bond work index (laboratory)10.500 kWh/t
Throughput (dry solids)150.00 t/h
Product of Rowland's efficiency factors (1 if none)1.0000 -
Measured mill power at the pinion (for the operating work index)900.00 kW

Applying the formula below gives:

ResultValue
Specific energy5.7248 kWh/t
Mill power required858.71 kW
Operating work index from measured power11.005 kWh/t
Circuit efficiency (laboratory over operating index)95.413 %

Open this example in the calculator and change any input.

Formula

\(W = 10 W_i\left(\frac{1}{\sqrt{P_{80}}} - \frac{1}{\sqrt{F_{80}}}\right) EF_x, \quad P = W T, \quad W_{io} = \frac{P_m/T}{10\left(1/\sqrt{P_{80}} - 1/\sqrt{F_{80}}\right)}\)

Variables

Symbol Meaning SI unit
\(F_{80}\) Feed 80 % passing size m
\(P_{80}\) Product 80 % passing size m
\(W_i\) Bond work index (laboratory) J/kg
\(T\) Throughput (dry solids) kg/s
\(EF_x\) Product of Rowland's efficiency factors (1 if none) -
\(P_m\) Measured mill power at the pinion (for the operating work index) W
\(W\) Specific energy J/kg
\(P\) Mill power required W
\(W_{io}\) Operating work index from measured power J/kg
\(W_i/W_{io}\) Circuit efficiency (laboratory over operating index) -

Method and standards

Bond's equation with Rowland's efficiency factors.

Where it is used

  • Sizing rod and ball mills.
  • Benchmarking grinding circuits.

Common mistakes

  • Using motor input instead of pinion power.
  • Applying the ball-mill index to SAG milling.

Assumptions and limits

  • Wet closed-circuit grinding; Bond's calibration range.

References

  • Wills and Finch
  • Wills' Mineral Processing Technology
  • 8th ed. (Butterworth-Heinemann, 2016)
  • ch. 5
  • eq. 5.4 (Bond, 1952) and ch. 7
  • eq. 7.11 (Rowland and Kjos, 1980)
  • Example 7.2

Questions and answers

What is the operating work index used for?

Compared with the laboratory index it shows how efficiently a circuit grinds; a rising operating index means harder ore or a less efficient circuit.

Which sizes go into the equation?

The 80 % passing sizes of the circuit feed and the circuit product (cyclone overflow), in micrometres.

What do the defaults represent?

Wills's Example 7.2: closed-circuit ball mill from 600 to 110 µm, Wi 10.5 kWh/t, 150 t/h (5.72 kWh/t, 859 kW), with 900 kW measured.

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.