FireCADCalc

Chlorine Dose, Hypochlorite Quantity and CT Value

Chlorine dose from demand and residual, chlorine per day for a flow, the quantity of hypochlorite or bleaching powder at its available chlorine, and the CT value.

Inputs

Examples: 500 m3/day with 10 % hypochloriteCooling water 200 m3/h, bleaching powder

About 0.1–0.15 for sodium hypochlorite solution, 0.3 for bleaching powder, 0.65–0.7 for calcium hypochlorite; from the supplier.

Results

CT uses the residual and the contact time; compare with the CT your regulator requires for the organism, pH and temperature.

Dose D + C_r2.3000mg/L
Chlorine per day11.040kg/d
Product per day36.800kg/d
Product volume per day1.5333L/h
CT value (mg·min/L)3.0000

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 500 m3/day with 10 % hypochlorite. The inputs, in the units selected above:

InputValue
Water flow500.00 m³/d
Chlorine demand1.5000 mg/L
Residual wanted0.50000 mg/L
Available chlorine of the product (mass fraction, w/w)10.000 %
Product density (solution)1,200.0 kg/m³
Contact time30.000 min

Applying the formula below gives:

ResultValue
Dose D + C_r2.0000 mg/L
Chlorine per day1.0000 kg/d
Product per day10.000 kg/d
Product volume per day0.34722 L/h
CT value (mg·min/L)15.000

Open this example in the calculator and change any input.

Formula

\(d = D + C_r, \quad \dot m = Q d, \quad \dot m_p = \frac{\dot m}{x}, \quad CT = C_r\, t\)

Variables

Symbol Meaning SI unit
\(Q\) Water flow m³/s
\(D\) Chlorine demand kg/m³
\(C_r\) Residual wanted kg/m³
\(x\) Available chlorine of the product (mass fraction, w/w) -
\(\rho\) Product density (solution) kg/m³
\(t\) Contact time s
\(d\) Dose D + C_r kg/m³
\(\dot m\) Chlorine per day kg/s
\(\dot m_p\) Product per day kg/s
\(\dot V_p\) Product volume per day m³/s
\(CT\) CT value (mg·min/L) -

Method and standards

Mass balance.

Where it is used

  • Drinking water and cooling water chlorination.
  • Dosing pump sizing.

Common mistakes

  • Forgetting demand.
  • Nominal strength of an old stock.

Assumptions and limits

  • Steady flow.
  • Available chlorine as a mass fraction. Hypochlorite sold by 'trade %' (g/L of available chlorine divided by 10) is a volume basis: divide it by the density in kg/L for x (10 % trade at 1.2 kg/L is 8.3 % w/w).

References

  • Mass balance of available chlorine; CT = residual × contact time (US EPA disinfection practice)

Questions and answers

500 m³/day with 1.5 mg/L demand and 0.5 residual?

2 mg/L dose: 1 kg of chlorine a day, 10 kg of 10 % hypochlorite.

Why does the product lose strength?

Hypochlorite solution decays with time, heat and light; check its strength.

CT?

0.5 mg/L for 30 minutes is 15 mg·min/L.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.