FireCADCalc

Steam Turbine Steam Rate (kg/kWh)

Theoretical and actual steam rate of a steam turbine in kg/kWh, and the steam flow needed for a given electrical output (IAPWS-IF97).

Thermal power plantSugar mill and cogenerationPulp and paperIAPWS-IF97 (water and steam)Steam turbineBoiler operation engineer (BOE) examinations

Inputs

Examples: 2 MW back-pressure set, 45 bar(a) / 400 °C to 4 bar(a)15 MW condensing, 66 bar(a) / 485 °C to 0.1 bar(a)500 kW, 17.5 bar(a) saturated to 3 bar(a)

Results

Actual steam rate3.7146kg/kWh
Steam flow for the output55,719kg/h
Theoretical steam rate2.9242kg/kWh
Isentropic enthalpy drop1,231.1kJ/kg

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 2 MW back-pressure set, 45 bar(a) / 400 °C to 4 bar(a). The inputs, in the units selected above:

InputValue
Inlet steam pressure (absolute)45.000 bar
Inlet steam conditionSuperheated at the temperature below
Inlet steam temperature (superheated only)400.00 °C
Exhaust pressure (absolute)400.00 kPa
Turbine isentropic efficiency75.000 %
Gearbox and generator efficiency95.000 %
Electrical output wanted2,000.0 kW

Applying the formula below gives:

ResultValue
Actual steam rate9.2527 kg/kWh
Steam flow for the output18,505 kg/h
Theoretical steam rate6.5925 kg/kWh
Isentropic enthalpy drop546.07 kJ/kg

Open this example in the calculator and change any input.

Formula

\(TSR = \frac{1}{h_1 - h_{2s}} \qquad ASR = \frac{1}{(h_1 - h_{2s})\,\eta_i\,\eta_g} \qquad \dot m_s = ASR \cdot P_{el}\)

Variables

Symbol Meaning SI unit
\(p_1\) inlet pressure, absolute Pa
\(\text{state}\) dry saturated or superheated inlet –
\(T_1\) inlet temperature (superheated) K
\(p_2\) exhaust pressure, absolute Pa
\(\eta_i\) turbine isentropic efficiency –
\(\eta_g\) gearbox and generator efficiency –
\(P_{el}\) electrical output wanted W
\(ASR\) actual steam rate kg/J
\(TSR\) theoretical steam rate kg/J
\(\dot m_s\) steam flow for the output kg/s
\(h_1 - h_{2s}\) isentropic enthalpy drop J/kg
\(h_1\), \(h_{2s}\) inlet and isentropic exhaust enthalpy J/kg

Method and standards

Steam rate from the isentropic enthalpy drop (FireCAD IAPWS-IF97) and the turbine and generator efficiencies. Shown in kg/kWh; 1 kWh = 3.6 MJ.

Where it is used

  • First sizing of a turbo-generator and its boiler.
  • Steam balance of a cogeneration plant: how much steam the power takes.
  • Comparing turbine offers at the same steam conditions.

Common mistakes

  • Quoting the theoretical steam rate as the turbine's consumption.
  • Forgetting the generator and gearbox losses.
  • Using one steam rate for all loads: part-load steam rates rise.

Assumptions and limits

  • Single expansion, constant efficiencies, steady flow.

References

  • IAPWS R7-97(2012) IF97
  • first law of thermodynamics

Questions and answers

What is a turbine's steam rate?

The steam it needs per kWh. Expanding from 45 bar(a) and 400 °C to 4 bar(a), the theoretical steam rate is 6.59 kg/kWh; at 75 % turbine and 95 % generator efficiency the actual rate is 9.25 kg/kWh, so 2 MW needs 18.5 t/h.

Why is a back-pressure turbine's steam rate so high?

Its enthalpy drop is small, so each kg makes little power. That is fine: the exhaust steam goes on to heat the process, so the fuel is used almost fully.

Is steam rate the same as heat rate?

No. Steam rate is kg of steam per kWh; heat rate is the heat added to that steam per kWh. Use the heat rate calculator for the second.

Method and article reviewed by FireCAD engineering on 11 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.