FireCADCalc

PRDS vs Back-Pressure Turbine (Power Lost)

Power a back-pressure steam turbine would make from steam now reduced through a PRDS valve, and its value per year, with both outlet steam states (IAPWS-IF97).

Thermal power plantSugar mill and cogenerationPulp and paperIAPWS-IF97 (water and steam)Steam turbineDesuperheater and PRDS

Inputs

Examples: 20 t/h, 45 bar(a) / 400 °C reduced to 4 bar(a)8 t/h, 17.5 bar(a) saturated to 3 bar(a)60 t/h, 66 bar(a) / 485 °C to 12 bar(a)

Results

The turbine exhaust carries 382 kJ/kg less than PRDS steam (the difference became power): the process gets less heat per kg, so a little more steam is needed for the same duty. That extra steam is not computed here.

Electrical power a turbine would make1,996.2kW
Value of that power per year (your currency)1.2776e+08
Steam temperature after the PRDS valve (before spray)367.17°C
Steam temperature after the turbine182.18°C
Turbine exhaust dryness (1 = dry or superheated)100.00%
Turbine exhaust enthalpy2,823.3kJ/kg

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 20 t/h, 45 bar(a) / 400 °C reduced to 4 bar(a). The inputs, in the units selected above:

InputValue
Steam flow through the PRDS20,000 kg/h
Inlet steam pressure (absolute)45.000 bar
Inlet steam conditionSuperheated at the temperature below
Inlet steam temperature (superheated only)400.00 °C
Process (reduced) pressure (absolute)400.00 kPa
Turbine isentropic efficiency70.000 %
Gearbox and generator efficiency94.000 %
Operating hours per year8,000.0 h
Value of electricity per kWh (your currency)8.0000 -

Applying the formula below gives:

ResultValue
Electrical power a turbine would make1,996.2 kW
Value of that power per year (your currency)1.2776e+08
Steam temperature after the PRDS valve (before spray)367.17 °C
Steam temperature after the turbine182.18 °C
Turbine exhaust dryness (1 = dry or superheated)100.00 %
Turbine exhaust enthalpy2,823.3 kJ/kg

Open this example in the calculator and change any input.

Formula

\(h_2 = h_1 - \eta_i\,\left[h_1 - h(p_2, s_1)\right] \qquad P_{el} = \eta_g\,\dot m_s\,(h_1 - h_2)\)

\(V = P_{el}\,t_{op}\,c_e \qquad T_{PRDS} = T(p_2, h_1)\)

Variables

Symbol Meaning SI unit
\(\dot m_s\) steam flow through the PRDS kg/s
\(p_1\) supply pressure, absolute Pa
\(\text{state}\) dry saturated or superheated supply –
\(T_1\) supply temperature (superheated) K
\(p_2\) process (reduced) pressure, absolute Pa
\(\eta_i\) turbine isentropic efficiency –
\(\eta_g\) gearbox and generator efficiency –
\(t_{op}\) operating hours per year s
\(c_e\) value of electricity per kWh –
\(P_{el}\) electrical power a turbine would make W
\(V\) value of that power per year –
\(T_{PRDS}\) steam temperature after the valve, before spray K
\(T_2\) steam temperature after the turbine K
\(x_2\) turbine exhaust dryness –
\(h_2\) turbine exhaust enthalpy J/kg
\(h_1\), \(s_1\) supply enthalpy and entropy J/kg, J/(kg·K)

Method and standards

The PRDS valve is isenthalpic (throttling); the turbine follows the isentropic-efficiency expansion. States by FireCAD's IAPWS-IF97. Energy in kWh for the value.

Where it is used

  • Screening letdown turbines and micro steam turbines for process plants.
  • Energy audits: showing the cost of reducing high-pressure steam through valves.
  • Cogeneration feasibility before asking turbine makers for offers.

Common mistakes

  • Counting full-load flow for all hours when the PRDS flow varies.
  • Forgetting that the process still needs the same heat: the boiler must make a little more steam.
  • Using a large-turbine efficiency for a small single-stage machine.

Assumptions and limits

  • Same steam flow through the turbine as through the PRDS; constant efficiencies; desuperheating not modelled.
  • The extra boiler steam needed to give the process the same heat is not computed; the note gives the enthalpy deficit per kg.
  • x₂ follows the property library: 1 for dry or superheated exhaust.

References

  • IAPWS R7-97(2012) IF97
  • first law of thermodynamics

Questions and answers

How much power is lost in a PRDS?

As much as a back-pressure turbine would make from the same steam. 20 t/h reduced from 45 bar(a) and 400 °C to 4 bar(a) could give about 2.0 MW with a 70 % efficient turbine and 94 % generator efficiency (the page default of 95 % gives about 2.02 MW), worth about 128 million a year at 8 per kWh over 8000 hours.

Does the process lose heat if a turbine replaces the PRDS?

A little: the power taken out comes from the steam's enthalpy, so the exhaust carries less heat per kg. The boiler supplies that extra heat, at boiler efficiency, which is still far cheaper than grid power in most plants.

Why is the PRDS steam so hot?

Throttling keeps the enthalpy, so steam from 45 bar(a) and 400 °C leaves the valve at about 367 °C at 4 bar(a); the spray water brings it down. A turbine exhaust is much cooler, about 182 °C here.

Method and article reviewed by FireCAD engineering on 11 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.