Worked example
Example: 30 bar 300 °C to 1.2 bar, 12 teeth, 400 mm, 0.4 mm. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Upstream pressure (absolute) | 30.000 bar |
| Upstream steam temperature (≤ saturation = dry saturated) | 300.00 °C |
| Downstream pressure (absolute) | 1.2000 bar |
| Number of throttles (teeth) | 12.000 - |
| Shaft diameter at the seal | 400.00 mm |
| Radial clearance | 0.40000 mm |
| Flow coefficient | 0.70000 - |
Applying the formula below gives:
| Result | Value |
|---|---|
| Clearance area | 502.65 mm² |
| Upstream specific volume | 0.081175 m³/kg |
| Leakage | 1,972.3 kg/h |
| Pressure ratio p_n/p_0 below which the last throttle chokes, 0.85/√(N + 1.5) | 0.23134 |
Open this example in the calculator and change any input.
Formula
\(\dot m = KA\sqrt{\frac{p_0}{v_0}}\sqrt{\frac{1 - (p_n/p_0)^2}{N - \ln(p_n/p_0)}}, \quad A = \pi Dc, \quad r_{cr} = \frac{0.85}{\sqrt{N + 1.5}}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(p_0\) | Upstream pressure (absolute) | Pa |
| \(T_0\) | Upstream steam temperature (≤ saturation = dry saturated) | K |
| \(p_n\) | Downstream pressure (absolute) | Pa |
| \(N\) | Number of throttles (teeth) | - |
| \(D\) | Shaft diameter at the seal | m |
| \(c\) | Radial clearance | m |
| \(K\) | Flow coefficient | - |
| \(A\) | Clearance area | m² |
| \(v_0\) | Upstream specific volume | m³/kg |
| \(\dot m\) | Leakage | kg/s |
| \(r_{cr}\) | Pressure ratio p_n/p_0 below which the last throttle chokes (Stodola) | - |
Method and standards
Martin's formula.
Where it is used
- Gland steam and leak-off estimates.
- Effect of worn seals on heat rate.
Common mistakes
- Using diametral instead of radial clearance.
- Applying it at choking pressure ratios with few teeth.
Assumptions and limits
- Straight-through or stepped labyrinth with flow coefficient K.
- Subsonic flow at the last throttle is assumed. A note appears when p_n/p_0 is below r_cr = 0.85/√(N + 1.5), Stodola's criterion for choking at the last throttle; the formula then overstates the leakage, and no choked-flow model is applied.
- At 22 MPa and above the upstream state is taken at the entered pressure and temperature.
References
- Martin (1908) labyrinth leakage formula
- as given in turbomachinery texts (e.g. Stodola; Kearton, Steam Turbine Theory and Practice)
Questions and answers
Why do more teeth leak less?
Each throttle takes part of the pressure drop and the kinetic energy is lost between teeth, so the flow per unit pressure difference falls roughly as 1/√N.
How much does clearance matter?
Leakage is directly proportional to clearance: a rub that doubles it doubles the leakage.
What do the defaults give?
30 bar, 300 °C steam to 1.2 bar through 12 teeth on a 400 mm shaft at 0.4 mm clearance: about 2 t/h.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.