FireCADCalc

Extraction Turbine Power and Heat Balance

Power of an extraction (pass-out) steam turbine from inlet steam, extraction pressure and flow, exhaust pressure and section efficiencies, with the extraction steam state.

Thermal power plantSugar mill and cogenerationPulp and paperIAPWS-IF97 (water and steam)Steam turbine

Inputs

Examples: 60 t/h at 66 bar(a) / 485 °C, 20 t/h extracted at 4 bar(a), condensing 0.1 bar(a)100 t/h at 105 bar(a) / 535 °C, 40 t/h at 12 bar(a), exhaust 4 bar(a)30 t/h at 45 bar(a) / 400 °C, 10 t/h at 8 bar(a), condensing 0.12 bar(a)

Results

Electrical power5,151.8kW
Shaft power, inlet to extraction2,606.0kW
Shaft power, extraction to exhaust2,816.9kW
Extraction steam temperature223.55°C
Extraction steam enthalpy2,892.8kJ/kg
Exhaust steam flow20,000kg/h
Exhaust dryness (1 = dry or superheated)91.420%
Exhaust enthalpy2,385.8kJ/kg

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 60 t/h at 66 bar(a) / 485 °C, 20 t/h extracted at 4 bar(a), condensing 0.1 bar(a). The inputs, in the units selected above:

InputValue
Inlet steam flow60,000 kg/h
Inlet steam pressure (absolute)66.000 bar
Inlet steam conditionSuperheated at the temperature below
Inlet steam temperature (superheated only)485.00 °C
Extraction pressure (absolute)4.0000 bar
Extraction steam flow20,000 kg/h
Exhaust pressure (absolute)10.000 kPa
Isentropic efficiency, inlet to extraction80.000 %
Isentropic efficiency, extraction to exhaust78.000 %
Gearbox and generator efficiency96.000 %

Applying the formula below gives:

ResultValue
Electrical power13,621 kW
Shaft power, inlet to extraction9,173.7 kW
Shaft power, extraction to exhaust5,014.5 kW
Extraction steam temperature185.00 °C
Extraction steam enthalpy2,829.3 kJ/kg
Exhaust steam flow40,000 kg/h
Exhaust dryness (1 = dry or superheated)91.393 %
Exhaust enthalpy2,378.0 kJ/kg

Open this example in the calculator and change any input.

Formula

\(h_x = h_1 - \eta_{HP}\,\left[h_1 - h(p_x, s_1)\right] \qquad h_2 = h_x - \eta_{LP}\,\left[h_x - h(p_2, s_x)\right]\)

\(P_{HP} = \dot m_1\,(h_1 - h_x) \qquad P_{LP} = (\dot m_1 - \dot m_x)\,(h_x - h_2) \qquad P_{el} = \eta_g\,(P_{HP} + P_{LP})\)

Variables

Symbol Meaning SI unit
\(\dot m_1\) inlet steam flow kg/s
\(p_1\) inlet pressure, absolute Pa
\(\text{state}\) dry saturated or superheated inlet –
\(T_1\) inlet temperature (superheated) K
\(p_x\) extraction pressure, absolute Pa
\(\dot m_x\) extraction flow kg/s
\(p_2\) exhaust pressure, absolute Pa
\(\eta_{HP}\) isentropic efficiency, inlet to extraction –
\(\eta_{LP}\) isentropic efficiency, extraction to exhaust –
\(\eta_g\) gearbox and generator efficiency –
\(P_{el}\) electrical power W
\(P_{HP}\) shaft power of the first section W
\(P_{LP}\) shaft power of the second section W
\(T_x\) extraction steam temperature K
\(h_x\) extraction steam enthalpy J/kg
\(\dot m_2\) exhaust steam flow kg/s
\(x_2\) exhaust dryness –
\(h_1\), \(h_2\) inlet and exhaust enthalpy J/kg
\(s_1\), \(s_x\) entropy at inlet and at extraction J/(kg·K)

Method and standards

Two expansions in series, each with its own isentropic efficiency, and a mass balance at the extraction; states by FireCAD's IAPWS-IF97.

Where it is used

  • Cogeneration in sugar, paper, fertiliser and refinery plants: power and process steam from one turbine.
  • Checking the power left after a new process steam demand.
  • First heat balances before the turbine maker's guarantee.

Common mistakes

  • Using one efficiency for both sections when the low-pressure section of a condensing turbine is usually less efficient.
  • Leaving out the minimum flow the second section needs for cooling.
  • Using gauge pressures.

Assumptions and limits

  • One extraction; steady flow; section efficiencies constant.
  • With all the steam extracted the LP section carries no flow: its exhaust state is not shown, and a note recalls the minimum LP cooling flow, which is the turbine maker's figure and is not checked here.

References

  • IAPWS R7-97(2012) IF97
  • first law of thermodynamics

Questions and answers

How do I calculate an extraction turbine's power?

Add the power of the two sections. 60 t/h at 66 bar(a) and 485 °C, with 20 t/h extracted at 4 bar(a) and the rest condensing at 0.1 bar(a), gives 9.17 MW in the first section and 5.01 MW in the second: 13.6 MW at the generator. The extraction steam is at 185 °C.

Why is the extraction steam superheated?

The turbine's losses reheat the steam, so with good inlet superheat the extraction leaves above saturation. Process users often desuperheat it.

Does more extraction mean less power?

Yes: extracted steam skips the second section. But it heats the process, so the overall fuel use of the site falls.

Method and article reviewed by FireCAD engineering on 11 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.