Worked example
Example: 60 t/h at 66 bar(a) / 485 °C, 20 t/h extracted at 4 bar(a), condensing 0.1 bar(a). The inputs, in the units selected above:
| Input | Value |
|---|---|
| Inlet steam flow | 60,000 kg/h |
| Inlet steam pressure (absolute) | 66.000 bar |
| Inlet steam condition | Superheated at the temperature below |
| Inlet steam temperature (superheated only) | 485.00 °C |
| Extraction pressure (absolute) | 4.0000 bar |
| Extraction steam flow | 20,000 kg/h |
| Exhaust pressure (absolute) | 10.000 kPa |
| Isentropic efficiency, inlet to extraction | 80.000 % |
| Isentropic efficiency, extraction to exhaust | 78.000 % |
| Gearbox and generator efficiency | 96.000 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| Electrical power | 13,621 kW |
| Shaft power, inlet to extraction | 9,173.7 kW |
| Shaft power, extraction to exhaust | 5,014.5 kW |
| Extraction steam temperature | 185.00 °C |
| Extraction steam enthalpy | 2,829.3 kJ/kg |
| Exhaust steam flow | 40,000 kg/h |
| Exhaust dryness (1 = dry or superheated) | 91.393 % |
| Exhaust enthalpy | 2,378.0 kJ/kg |
Open this example in the calculator and change any input.
Formula
\(h_x = h_1 - \eta_{HP}\,\left[h_1 - h(p_x, s_1)\right] \qquad h_2 = h_x - \eta_{LP}\,\left[h_x - h(p_2, s_x)\right]\)
\(P_{HP} = \dot m_1\,(h_1 - h_x) \qquad P_{LP} = (\dot m_1 - \dot m_x)\,(h_x - h_2) \qquad P_{el} = \eta_g\,(P_{HP} + P_{LP})\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(\dot m_1\) | inlet steam flow | kg/s |
| \(p_1\) | inlet pressure, absolute | Pa |
| \(\text{state}\) | dry saturated or superheated inlet | – |
| \(T_1\) | inlet temperature (superheated) | K |
| \(p_x\) | extraction pressure, absolute | Pa |
| \(\dot m_x\) | extraction flow | kg/s |
| \(p_2\) | exhaust pressure, absolute | Pa |
| \(\eta_{HP}\) | isentropic efficiency, inlet to extraction | – |
| \(\eta_{LP}\) | isentropic efficiency, extraction to exhaust | – |
| \(\eta_g\) | gearbox and generator efficiency | – |
| \(P_{el}\) | electrical power | W |
| \(P_{HP}\) | shaft power of the first section | W |
| \(P_{LP}\) | shaft power of the second section | W |
| \(T_x\) | extraction steam temperature | K |
| \(h_x\) | extraction steam enthalpy | J/kg |
| \(\dot m_2\) | exhaust steam flow | kg/s |
| \(x_2\) | exhaust dryness | – |
| \(h_1\), \(h_2\) | inlet and exhaust enthalpy | J/kg |
| \(s_1\), \(s_x\) | entropy at inlet and at extraction | J/(kg·K) |
Method and standards
Two expansions in series, each with its own isentropic efficiency, and a mass balance at the extraction; states by FireCAD's IAPWS-IF97.
Where it is used
- Cogeneration in sugar, paper, fertiliser and refinery plants: power and process steam from one turbine.
- Checking the power left after a new process steam demand.
- First heat balances before the turbine maker's guarantee.
Common mistakes
- Using one efficiency for both sections when the low-pressure section of a condensing turbine is usually less efficient.
- Leaving out the minimum flow the second section needs for cooling.
- Using gauge pressures.
Assumptions and limits
- One extraction; steady flow; section efficiencies constant.
- With all the steam extracted the LP section carries no flow: its exhaust state is not shown, and a note recalls the minimum LP cooling flow, which is the turbine maker's figure and is not checked here.
References
- IAPWS R7-97(2012) IF97
- first law of thermodynamics
Questions and answers
How do I calculate an extraction turbine's power?
Add the power of the two sections. 60 t/h at 66 bar(a) and 485 °C, with 20 t/h extracted at 4 bar(a) and the rest condensing at 0.1 bar(a), gives 9.17 MW in the first section and 5.01 MW in the second: 13.6 MW at the generator. The extraction steam is at 185 °C.
Why is the extraction steam superheated?
The turbine's losses reheat the steam, so with good inlet superheat the extraction leaves above saturation. Process users often desuperheat it.
Does more extraction mean less power?
Yes: extracted steam skips the second section. But it heats the process, so the overall fuel use of the site falls.
Method and article reviewed by FireCAD engineering on 11 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.