FireCADCalc

Back-Pressure vs Extraction-Condensing Turbine Power

Power of a back-pressure turbine on process steam only against an extraction-condensing turbine on more steam, with condenser heat and extra steam rate (IF97).

Process steam and utilitiesSugar mill and cogenerationDistillery and ethanolPulp and paperIAPWS-IF97 (water and steam)Steam turbine

Inputs

Examples: 87 bar, 515 °C67 bar, 495 °C

Results

Same isentropic efficiency is applied to each section; real machines differ by section and load.

No condensing flow, so no extra power and no extra steam rate.

Power, back-pressure turbine13.536MW
Power, extraction-condensing turbine13.536MW
Extra power0MW
Condenser heat rejected0MW

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 87 bar, 515 °C. The inputs, in the units selected above:

InputValue
Turbine inlet pressure (absolute)87.000 bar
Turbine inlet temperature515.00 °C
Process (exhaust or extraction) pressure (absolute)2.5000 bar
Condenser pressure (absolute)10.000 kPa
Process steam demand100.00 t/h
Steam to the extraction-condensing turbine130.00 t/h
Isentropic efficiency (each section)80.000 %
Gearbox and generator efficiency96.000 %

Applying the formula below gives:

ResultValue
Power, back-pressure turbine17.966 MW
Power, extraction-condensing turbine26.497 MW
Extra power8.5308 MW
Condenser heat rejected18.086 MW
Extra steam per extra kWh3.5167 kg/kWh

Open this example in the calculator and change any input.

Formula

\(P_{BP} = \dot m_p (h_1 - h_e)\eta_g, \quad P_{EC} = [\dot m_t (h_1 - h_e) + (\dot m_t - \dot m_p)(h_e - h_c)]\eta_g\)

Variables

Symbol Meaning SI unit
\(p_1\) Turbine inlet pressure (absolute) Pa
\(T_1\) Turbine inlet temperature K
\(p_e\) Process (exhaust or extraction) pressure (absolute) Pa
\(p_c\) Condenser pressure (absolute) Pa
\(\dot m_p\) Process steam demand kg/s
\(\dot m_t\) Steam to the extraction-condensing turbine kg/s
\(\eta_s\) Isentropic efficiency (each section) -
\(\eta_g\) Gearbox and generator efficiency -
\(P_{BP}\) Power, back-pressure turbine W
\(P_{EC}\) Power, extraction-condensing turbine W
\(\Delta P\) Extra power W
\(\dot Q_c\) Condenser heat rejected W
\(SR\) Extra steam per extra kWh kg/J

Method and standards

IF97 expansion.

Where it is used

  • Cogeneration configuration studies.
  • Sugar and distillery turbine selection.

Common mistakes

  • Absolute and gauge pressures mixed.

Assumptions and limits

  • Same efficiency for both sections; a note warns when the condenser exhaust is wetter than about 88 %.
  • The extra steam (ṁ_t − ṁ_p) needs extra boiler fuel, which this comparison does not count: weigh the extra power against that fuel.
  • With no condensing flow the extra steam rate is not shown.
  • The inlet must be superheated (or supercritical) steam; a liquid inlet state is rejected.

References

  • Expansion with isentropic efficiency per section; IAPWS-IF97 enthalpies and entropies

Questions and answers

Why does the condensing tail cost so much steam per kWh?

Most of the condensing steam's heat goes to the condenser, not the shaft.

When is EC worth it?

When surplus fuel (bagasse, off-season) and an export tariff exist.

Season and off-season?

EC turbines run the off-season fully condensing; BP turbines stop with the process.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.