FireCADCalc

Furnace Gas Residence Time and Volumetric Heat Release

Flue gas volume flow at furnace temperature (ideal gas), gas residence time in the furnace and the volumetric heat release from the heat input.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationDistillery and ethanolBurner and furnace

Inputs

Examples: Bagasse furnaceSlop furnace

Results

Biomass and slop furnaces need longer residence times than oil or gas to burn out volatiles and char.

Gas density at furnace temperature0.27336kg/m³
Gas volume flow329,239m³/h
Residence time3.2803s
Volumetric heat release133.33kW/m³

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Bagasse furnace. The inputs, in the units selected above:

InputValue
Furnace volume450.00 m³
Flue gas flow160.00 t/h
Mean furnace gas temperature1,000.0 °C
Flue gas molar mass28.500 kg/kmol
Furnace pressure (absolute)101.33 kPa
Heat input from fuel (GCV or NCV, as your limit states)75.000 MW

Applying the formula below gives:

ResultValue
Gas density at furnace temperature0.27280 kg/m³
Gas volume flow586,506 m³/h
Residence time2.7621 s
Volumetric heat release166.67 kW/m³

Open this example in the calculator and change any input.

Formula

\(\rho_g = \frac{p M_g}{1000\,R\,T_f}, \quad t_r = \frac{V_f \rho_g}{\dot m_g}, \quad q_v = \frac{\dot Q}{V_f}\)

Variables

Symbol Meaning SI unit
\(V_f\) Furnace volume m³
\(\dot m_g\) Flue gas flow kg/s
\(T_f\) Mean furnace gas temperature K
\(M_g\) Flue gas molar mass kg/kmol
\(p\) Furnace pressure (absolute) Pa
\(\dot Q\) Heat input (fuel) W
\(\rho_g\) Gas density at furnace temperature kg/m³
\(\dot V_g\) Gas volume flow m³/s
\(t_r\) Residence time s
\(q_v\) Volumetric heat release W/m³
\(R\) universal gas constant, 8.314 J/(mol·K) (the 1000 converts \(M_g\) from kg/kmol) J/(mol·K)

Method and standards

Ideal-gas density at the mean furnace temperature; residence time is the furnace volume over the gas volume flow.

Where it is used

  • Furnace sizing and checks.
  • Fuel change studies.

Common mistakes

  • Gas flow at normal conditions used as actual.

Assumptions and limits

  • Uniform temperature; plug flow through the whole volume.
  • The volumetric heat release is on the basis (GCV or NCV) of the heat input entered.
  • A note appears below 2 s, the residence time waste-fuel rules often require.

References

  • Ideal gas density ρ = pM/(RT); residence time = V/V̇; heat release = Q/V

Questions and answers

Why residence time?

Fuel needs time at temperature to burn out; emissions rules for waste fuels often ask for it.

Mean gas temperature?

Between the flame and the furnace exit; use a design estimate.

Molar mass of flue gas?

Close to 28–29 kg/kmol; wet biomass flue gas is a little lighter.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.