FireCADCalc

Two-Phase Friction Multiplier (Lockhart–Martinelli, Chisholm C)

Martinelli parameter and Chisholm two-phase friction multiplier for steam–water from pressure and quality (IF97 properties), and the two-phase pressure drop.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationDistillery and ethanolIAPWS-IF97 (water and steam)Boiler

Inputs

Examples: 70 bar, 10 %Low pressure flashing lineViscous liquid, turbulent vapour (C = 12)Both viscous (C = 5)

The form of the Martinelli parameter follows C: 20 turbulent liquid and vapour, 12 viscous liquid and turbulent vapour, 10 turbulent liquid and viscous vapour, 5 both viscous. Other values use the turbulent–turbulent form.
Total flow over the tube bore area. Used for the Reynolds numbers, which set the X form when C is 12 or 10 and check the regime.

Results

Δp_l is the friction drop of the liquid part of the flow, (1 − x)ṁ, flowing alone in the same tube.

Martinelli parameter, in the form set by C0.29510
Reynolds number of the liquid flowing alone1,095.7
Reynolds number of the vapour flowing alone5,293.9
Two-phase multiplier53.148
Two-phase frictional pressure drop26.574kPa

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 70 bar, 10 %. The inputs, in the units selected above:

InputValue
Pressure (absolute)70.000 bar
Steam quality10.000 %
Chisholm constant: 20 tt, 12 vt, 10 tv, 5 vv (liquid–vapour; t turbulent, v viscous)20.000 -
Pressure drop of the liquid flowing alone2.0000 kPa
Total mass flux1,000.0 kg/(m²·s)
Tube inside diameter50.000 mm

Applying the formula below gives:

ResultValue
Martinelli parameter, in the form set by C1.8792
Reynolds number of the liquid flowing alone493,063
Reynolds number of the vapour flowing alone264,697
Two-phase multiplier11.926
Two-phase frictional pressure drop23.852 kPa

Open this example in the calculator and change any input.

Formula

\(Re_l = \frac{G(1-x)D}{\mu_l}, \quad Re_v = \frac{G x D}{\mu_v}, \quad f = \frac{16}{Re} \text{ (viscous)} \text{ or } 0.046\,Re^{-0.2} \text{ (turbulent)}\)

\(X^2 = \frac{f_l}{f_v}\left(\frac{1-x}{x}\right)^2 \frac{\rho_v}{\rho_l}, \quad \phi_l^2 = 1 + \frac{C}{X} + \frac{1}{X^2}, \quad \Delta p_{tp} = \phi_l^2\,\Delta p_l\)

For both phases turbulent this is \(X_{tt} = \left(\frac{1-x}{x}\right)^{0.9}\left(\frac{\rho_v}{\rho_l}\right)^{0.5}\left(\frac{\mu_l}{\mu_v}\right)^{0.1}\).

Variables

Symbol Meaning SI unit
\(p\) Pressure (absolute) Pa
\(x\) Steam quality -
\(C\) Chisholm constant: 20 tt, 12 vt, 10 tv, 5 vv (liquid–vapour; t turbulent, v viscous) -
\(G\) Total mass flux kg/(m²·s)
\(D\) Tube inside diameter m
\(\Delta p_l\) Pressure drop of the liquid flowing alone Pa
\(X\) Martinelli parameter, in the form set by C -
\(X_{tt}\) X with both phases turbulent -
\(Re_l\), \(Re_v\) Reynolds numbers of the liquid and the vapour flowing alone -
\(f\), \(f_l\), \(f_v\) Fanning friction factor; of the liquid and of the vapour flowing alone -
\(\rho_l\), \(\rho_v\) Saturated liquid and vapour densities (IF97) kg/m³
\(\mu_l\), \(\mu_v\) Saturated liquid and vapour viscosities (IAPWS 2008) Pa·s
\(\phi_l^2\) Two-phase multiplier -
\(\Delta p_{tp}\) Two-phase frictional pressure drop Pa

Method and standards

Lockhart–Martinelli separated-flow model with Chisholm's form of the liquid multiplier. The Martinelli parameter X is the square root of the ratio of the liquid-alone to the vapour-alone friction gradients, each with the viscous (16/Re) or turbulent (0.046 Re^−0.2) friction factor that the chosen C stands for, as Lockhart and Martinelli and Chisholm define it. Saturated-liquid and vapour properties from IAPWS-IF97 and IAPWS 2008. A note appears when the Reynolds numbers (viscous below 1000, turbulent above 2000) do not match the regime of C.

Where it is used

  • Riser and evaporator pressure drop.
  • Flashing lines.

Common mistakes

  • Total flow used for the liquid-alone drop.

Assumptions and limits

  • Separated-flow model.
  • The form of X follows C (20, 12, 10 or 5); any other C uses the turbulent–turbulent form.

References

  • Lockhart and Martinelli
  • Chem. Eng. Prog. 45 (1949); Chisholm
  • Int. J. Heat Mass Transfer 10 (1967): φ_l² = 1 + C/X + 1/X²; Collier and Thome
  • Convective Boiling and Condensation; X_tt with IAPWS-IF97 densities and IAPWS 2008 viscosities

Questions and answers

What is Δp_l?

The friction loss if only the liquid fraction of the flow ran in the pipe.

Which C?

20 when both phases are turbulent; 12, 10 or 5 for the laminar combinations.

Accuracy?

Scatter of ±30 % or more is normal for two-phase friction correlations.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.