FireCADCalc

Thick Cylinder: Thermal and Pressure Hoop Stress

Inner and outer hoop stresses of a thick cylinder (drum, header) from a steady through-wall temperature difference plus internal pressure (Lamé).

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationDistillery and ethanolBoiler

Inputs

Examples: Drum 1.2 m bore, 90 mmHeader, outside hotter

Results

Steady logarithmic temperature profile; during start-up the transient profile differs (see the drum warm-up calculator). Design limits come from the applicable code.

Thermal hoop stress, inner surface-56.849MPa
Thermal hoop stress, outer surface51.794MPa
Pressure hoop stress, inner surface32.407MPa
Pressure hoop stress, outer surface27.907MPa
Total hoop stress, inner surface-24.442MPa
Total hoop stress, outer surface79.701MPa

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Drum 1.2 m bore, 90 mm. The inputs, in the units selected above:

InputValue
Inner radius0.60000 m
Outer radius0.69000 m
Inner minus outer surface temperature30.000 K
Internal pressure (gauge)45.000 bar
Young's modulus195.00 GPa
Linear expansion coefficient13.000 µm/(m·K)
Poisson's ratio0.30000 -

Applying the formula below gives:

ResultValue
Thermal hoop stress, inner surface-56.849 MPa
Thermal hoop stress, outer surface51.794 MPa
Pressure hoop stress, inner surface32.407 MPa
Pressure hoop stress, outer surface27.907 MPa
Total hoop stress, inner surface-24.442 MPa
Total hoop stress, outer surface79.701 MPa

Open this example in the calculator and change any input.

Formula

\(\sigma_{\theta,T}(r_i) = \frac{E\beta\Delta T}{2(1-\nu)\ln(r_o/r_i)}\left[1 - \frac{2r_o^2}{r_o^2 - r_i^2}\ln\frac{r_o}{r_i}\right], \quad \sigma_{\theta,p}(r_i) = p\frac{r_o^2 + r_i^2}{r_o^2 - r_i^2}\)

\(\sigma_{\theta,T}(r_o) = \frac{E\beta\Delta T}{2(1-\nu)\ln(r_o/r_i)}\left[1 - \frac{2r_i^2}{r_o^2 - r_i^2}\ln\frac{r_o}{r_i}\right], \quad \sigma_{\theta,p}(r_o) = p\frac{2r_i^2}{r_o^2 - r_i^2}, \quad \sigma_\theta = \sigma_{\theta,T} + \sigma_{\theta,p}\)

Variables

Symbol Meaning SI unit
\(r_i\) Inner radius m
\(r_o\) Outer radius m
\(\Delta T\) Inner minus outer surface temperature K
\(p\) Internal pressure (gauge) Pa
\(E\) Young's modulus Pa
\(\beta\) Linear expansion coefficient 1/K
\(\nu\) Poisson's ratio -
\(\sigma_{\theta,T}(r_i)\) Thermal hoop stress, inner surface Pa
\(\sigma_{\theta,T}(r_o)\) Thermal hoop stress, outer surface Pa
\(\sigma_{\theta,p}(r_i)\) Pressure hoop stress, inner surface Pa
\(\sigma_{\theta,p}(r_o)\) Pressure hoop stress, outer surface Pa
\(\sigma_\theta(r_i)\) Total hoop stress, inner surface Pa
\(\sigma_\theta(r_o)\) Total hoop stress, outer surface Pa

Method and standards

Thermal hoop stresses of a long cylinder with a steady logarithmic temperature distribution through the wall (Timoshenko and Goodier), added to the Lamé hoop stresses from internal gauge pressure at the inner and outer surfaces.

Where it is used

  • Drum and header stress checks.
  • Teaching thermal stress.

Common mistakes

  • Sign of ΔT reversed.

Assumptions and limits

  • Long cylinder, elastic, steady.
  • Hoop stresses only. The axial thermal stress (equal to the hoop thermal stress at the surfaces for a long cylinder with free ends) and the radial pressure stress (−p inside) are not shown, so no equivalent (Tresca or von Mises) stress is given for comparison with allowables.

References

  • Thermal stresses in a long thick cylinder with a steady logarithmic temperature profile (Timoshenko and Goodier, Theory of Elasticity, 3rd ed., McGraw-Hill, 1970); Lamé pressure stresses

Questions and answers

Which way does the thermal stress act?

When the inside is hotter, the inner surface is in compression and the outer in tension.

Why add pressure stress?

The surfaces see both; heating from inside relieves the inner pressure tension.

Is this the start-up case?

No, it is the steady profile; fast transients give larger differences.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.