Worked example
Example: 60 kW/m², 184 °C water, 4 mm steel, 1 mm scale of 1 W/(m·K). The inputs, in the units selected above:
| Input | Value |
|---|---|
| Heat flux through the tube wall | 60.000 kW/m² |
| Boiler water temperature (saturation) | 184.00 °C |
| Water-side (boiling) coefficient | 20,000 W/(m²·K) |
| Tube wall thickness | 4.0000 mm |
| Conductivity of the tube steel | 45.000 W/(m·K) |
| Scale thickness | 1.0000 mm |
| Conductivity of the scale | 1.0000 W/(m·K) |
Applying the formula below gives:
| Result | Value |
|---|---|
| Water-side metal temperature, clean tube | 187.00 °C |
| Gas-side metal temperature, clean tube | 192.33 °C |
| Gas-side metal temperature with scale | 252.33 °C |
| Metal temperature rise caused by the scale | 60.000 K |
| Thermal resistance of the scale t_s / k_s | 0.001000 m²·K/W |
Open this example in the calculator and change any input.
Formula
\(T_{in} = T_w + \frac{q}{h_w}, \quad T_{o,0} = T_{in} + q\, \frac{t_m}{k_m}\)
\(\Delta T_s = q\, \frac{t_s}{k_s}, \quad T_o = T_{o,0} + \Delta T_s, \quad T_{in,s} = T_{in} + \Delta T_s\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(q\) | Heat flux through the tube wall | W/m² |
| \(T_w\) | Boiler water temperature (saturation) | K |
| \(h_w\) | Water-side (boiling) coefficient | W/(m²·K) |
| \(t_m\) | Tube wall thickness | m |
| \(k_m\) | Conductivity of the tube steel | W/(m·K) |
| \(t_s\) | Scale thickness | m |
| \(k_s\) | Conductivity of the scale | W/(m·K) |
| \(T_{in}\) | Water-side metal temperature, clean tube | K |
| \(T_{o,0}\) | Gas-side metal temperature, clean tube | K |
| \(T_o\) | Gas-side metal temperature with scale | K |
| \(\Delta T_s\) | Metal temperature rise caused by the scale | K |
| \(R_s\) | Thermal resistance of the scale t_s / k_s | m²·K/W |
| \(T_{in,s}\) | water-side metal temperature behind the scale (not an output) | K |
Method and standards
At one heat flux each layer's temperature drop is q × its thermal resistance; scale adds a resistance t_s/k_s between the metal and the water.
Worked example
A tube at 60 kW/m² has boiler water at 184 °C, water-side coefficient 20 000 W/(m²·K), 4 mm steel wall (45 W/(m·K)) and 1 mm of scale (1 W/(m·K)).
- Water side of metal = 184 + 60 000/20 000 = 187 °C
- Gas side, clean = 187 + 60 000 × 0.004/45 = 192.3 °C
- Scale adds 60 000 × 0.001/1 = 60 K: gas side 252.3 °C
Where it is used
- Boiler attendant and operator examinations: why feedwater must be treated.
- Investigating tube bulges and failures.
- Justifying water treatment and blowdown.
Common mistakes
- Using a scale conductivity far from the real scale (it varies tenfold).
- Assuming the heat flux falls in proportion.
- Ignoring that the hottest tubes have the highest flux.
Assumptions and limits
- Flat-wall layers; same heat flux with and without scale, and the same flux through every layer. For a thick tube the flux on the inside surface is higher than on the outside by the diameter ratio; enter the inside-surface flux to be on the safe side for the water film and scale.
- A note appears when the gas-side metal is above about 450 °C; compare the result with the allowable temperature of your tube material.
- Scale conductivity entered by the user.
References
- One-dimensional conduction through layers in series (Fourier's law)
Questions and answers
How much hotter does 1 mm of scale make a tube at 60 kW/m²?
With a scale conductivity of 1 W/(m·K), 60 K: the gas-side metal goes from 192 °C to 252 °C.
Why is scale dangerous?
The heat must still pass, so the metal runs hotter until it creeps or bulges. 0.5 mm of porous silicate scale at 150 kW/m² can add over 350 K.
Does scale waste fuel?
Some, but mostly the gas leaves hotter. Overheating and tube failure are the bigger danger.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.