FireCADCalc

Fatigue Life by Basquin and Damage by Miner's Rule

Cycles to failure at a stress amplitude by Basquin's law with your constants, and the Miner's rule damage and remaining life for up to three stress blocks.

Inputs

Examples: Three blocksTwo blocks, steeper line

From fatigue data for the material and surface.

Block 1

Block 2

Block 3

Results

Damage reaches 1: failure is predicted.

Block 1: cycles to failure4,731.3
Block 2: cycles to failure52,016
Miner damage sum2.0180
Repeats of the block sequence left (1/D − 1)-0.50447

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Three blocks. The inputs, in the units selected above:

InputValue
Fatigue strength coefficient900.00 MPa
Fatigue strength exponent-0.090000 -
Block 1: stress amplitude300.00 MPa
Block 1: cycles applied20,000 -
Block 2: stress amplitude250.00 MPa
Block 2: cycles applied100,000 -
Block 3: stress amplitude200.00 MPa
Block 3: cycles applied500,000 -

Applying the formula below gives:

ResultValue
Block 1: cycles to failure100,073
Block 2: cycles to failure758,768
Block 3: cycles to failure9,054,966
Miner damage sum0.38686
Repeats of the block sequence left (1/D − 1)1.5849

Open this example in the calculator and change any input.

Formula

\(N_f = \frac{1}{2}\left(\frac{\sigma_a}{\sigma_f'}\right)^{1/b}, \quad D = \sum\frac{n_i}{N_{f,i}}\)

Variables

Symbol Meaning SI unit
\(\sigma_f'\) Fatigue strength coefficient Pa
\(b\) Fatigue strength exponent -
\(\sigma_{a1}\) Block 1: stress amplitude Pa
\(n_{1}\) Block 1: cycles applied -
\(\sigma_{a2}\) Block 2: stress amplitude Pa
\(n_{2}\) Block 2: cycles applied -
\(\sigma_{a3}\) Block 3: stress amplitude Pa
\(n_{3}\) Block 3: cycles applied -
\(N_{f1}\) Block 1: cycles to failure -
\(N_{f2}\) Block 2: cycles to failure -
\(N_{f3}\) Block 3: cycles to failure -
\(D\) Miner damage sum -
\(R\) Repeats of the block sequence left (1/D − 1) -

Method and standards

Basquin and Miner.

Where it is used

  • Fatigue checks of rotating and vibrating parts.
  • Remaining life estimates.

Common mistakes

  • Cycles vs reversals (2N).
  • Ignoring mean stress and notches.

Assumptions and limits

  • High-cycle, fully reversed.
  • No endurance limit: every amplitude above zero adds damage, which is conservative for amplitudes below the endurance limit. A block of zero amplitude adds none and its cycles to failure are not shown.
  • No mean-stress correction: correct the amplitudes first.

References

  • Basquin (1910) σ_a = σ_f'(2N_f)^b; Palmgren–Miner linear damage D = Σ n_i/N_i

Questions and answers

Blocks at 300, 250 and 200 MPa with the default constants?

Damage about 0.39.

What do the constants mean?

σ_f' is the stress for one reversal; b sets the slope of the S-N line.

Mean stress?

Correct the amplitude first (Goodman, Gerber or Morrow).

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.