FireCADCalc

Roll Crusher: Nip Angle, Largest Feed and Capacity

Largest particle crushing rolls can grip for a gap and nip angle, the friction needed and its fall with speed, and the ribbon capacity of the rolls.

Inputs

Examples: 1,000 mm rolls, 10 mm gap, 20 deg nipCoarse rolls 1,500 mm, 40 mm gapSmall laboratory rolls 250 mm

Results

Rolls must be starvation-fed and run in closed circuit with a screen; actual capacity is about 25 % of the ribbon. Reduction ratios above 4 are rare.

At this speed the kinetic friction is lower (Wills eq. 6.5): coarse feed may slip; slow the rolls or reduce the nip angle.

Largest particle gripped77.390mm
Reduction ratio1.9348
Largest nip angle for the static friction33.398°
Peripheral speed3.9270m/s
Kinetic coefficient of friction at this speed0.065934
Largest nip angle for the kinetic friction7.5446°
Theoretical ribbon capacity839.75t/h
Expected actual capacity251.92t/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 1,000 mm rolls, 10 mm gap, 20 deg nip. The inputs, in the units selected above:

InputValue
Roll diameter1,000.0 mm
Gap between the rolls (setting)10.000 mm
Angle of nip20.000 °
Static coefficient of friction (steel on ore 0.2–0.3)0.25000 -
Roll speed60.000 rpm
Roll width600.00 mm
Density of the feed material1.6000 g/cm³
Actual capacity as a fraction of the ribbon (about 0.25)25.000 %

Applying the formula below gives:

ResultValue
Largest particle gripped25.581 mm
Reduction ratio2.5581
Largest nip angle for the static friction28.072 °
Peripheral speed3.1416 m/s
Kinetic coefficient of friction at this speed0.056910
Largest nip angle for the kinetic friction6.5144 °
Theoretical ribbon capacity108.57 t/h
Expected actual capacity27.143 t/h

Open this example in the calculator and change any input.

Formula

\(\cos\frac{\theta}{2} = \frac{R + a}{R + r}, \quad \mu \geq \tan\frac{\theta}{2}, \quad \mu_k = \frac{1 + 1.12v}{1 + 6v}\mu, \quad Q = 188.5 N D W \rho d\ (\text{kg/h})\)

Variables

Symbol Meaning SI unit
\(D\) Roll diameter m
\(2a\) Gap between the rolls (setting) m
\(\theta\) Angle of nip rad
\(\mu\) Static coefficient of friction (steel on ore 0.2–0.3) -
\(N\) Roll speed 1/s
\(W\) Roll width m
\(\rho_s\) Density of the feed material kg/m³
\(\eta\) Actual capacity as a fraction of the ribbon (about 0.25) -
\(2r\) Largest particle gripped m
\(r/a\) Reduction ratio -
\(\theta_{max}\) Largest nip angle for the static friction rad
\(v\) Peripheral speed m/s
\(\mu_k\) Kinetic coefficient of friction at this speed -
\(\theta_{max,k}\) Largest nip angle for the kinetic friction rad
\(Q\) Theoretical ribbon capacity kg/s
\(\eta Q\) Expected actual capacity kg/s

Method and standards

Nip geometry, friction and ribbon capacity.

Where it is used

  • Selecting rolls for secondary and tertiary crushing.
  • Coal and soft-ore crushing.

Common mistakes

  • Using the radius as the particle size.
  • Choke-feeding rolls.

Assumptions and limits

  • Spherical particles; smooth rolls.

References

  • Wills and Finch
  • Wills' Mineral Processing Technology
  • 8th ed. (Butterworth-Heinemann, 2016)
  • ch. 6
  • eqs. 6.3-6.7 and Table 6.1

Questions and answers

Why does speed matter?

Friction falls with peripheral speed, so coarse feed (large nip angle) needs slow rolls while fine feed can run faster for capacity.

Why is the actual capacity only a quarter of the ribbon?

The ribbon assumes a solid band of rock between the rolls; real feed has voids and is not continuous.

What do the defaults represent?

1,000 mm rolls with a 10 mm gap, 20° nip and μ = 0.25, 60 rpm, 0.6 m wide on 1.6 t/m³ material.

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.