Worked example
Example: 1,000 mm rolls, 10 mm gap, 20 deg nip. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Roll diameter | 1,000.0 mm |
| Gap between the rolls (setting) | 10.000 mm |
| Angle of nip | 20.000 ° |
| Static coefficient of friction (steel on ore 0.2–0.3) | 0.25000 - |
| Roll speed | 60.000 rpm |
| Roll width | 600.00 mm |
| Density of the feed material | 1.6000 g/cm³ |
| Actual capacity as a fraction of the ribbon (about 0.25) | 25.000 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| Largest particle gripped | 25.581 mm |
| Reduction ratio | 2.5581 |
| Largest nip angle for the static friction | 28.072 ° |
| Peripheral speed | 3.1416 m/s |
| Kinetic coefficient of friction at this speed | 0.056910 |
| Largest nip angle for the kinetic friction | 6.5144 ° |
| Theoretical ribbon capacity | 108.57 t/h |
| Expected actual capacity | 27.143 t/h |
Open this example in the calculator and change any input.
Formula
\(\cos\frac{\theta}{2} = \frac{R + a}{R + r}, \quad \mu \geq \tan\frac{\theta}{2}, \quad \mu_k = \frac{1 + 1.12v}{1 + 6v}\mu, \quad Q = 188.5 N D W \rho d\ (\text{kg/h})\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(D\) | Roll diameter | m |
| \(2a\) | Gap between the rolls (setting) | m |
| \(\theta\) | Angle of nip | rad |
| \(\mu\) | Static coefficient of friction (steel on ore 0.2–0.3) | - |
| \(N\) | Roll speed | 1/s |
| \(W\) | Roll width | m |
| \(\rho_s\) | Density of the feed material | kg/m³ |
| \(\eta\) | Actual capacity as a fraction of the ribbon (about 0.25) | - |
| \(2r\) | Largest particle gripped | m |
| \(r/a\) | Reduction ratio | - |
| \(\theta_{max}\) | Largest nip angle for the static friction | rad |
| \(v\) | Peripheral speed | m/s |
| \(\mu_k\) | Kinetic coefficient of friction at this speed | - |
| \(\theta_{max,k}\) | Largest nip angle for the kinetic friction | rad |
| \(Q\) | Theoretical ribbon capacity | kg/s |
| \(\eta Q\) | Expected actual capacity | kg/s |
Method and standards
Nip geometry, friction and ribbon capacity.
Where it is used
- Selecting rolls for secondary and tertiary crushing.
- Coal and soft-ore crushing.
Common mistakes
- Using the radius as the particle size.
- Choke-feeding rolls.
Assumptions and limits
- Spherical particles; smooth rolls.
References
- Wills and Finch
- Wills' Mineral Processing Technology
- 8th ed. (Butterworth-Heinemann, 2016)
- ch. 6
- eqs. 6.3-6.7 and Table 6.1
Questions and answers
Why does speed matter?
Friction falls with peripheral speed, so coarse feed (large nip angle) needs slow rolls while fine feed can run faster for capacity.
Why is the actual capacity only a quarter of the ribbon?
The ribbon assumes a solid band of rock between the rolls; real feed has voids and is not continuous.
What do the defaults represent?
1,000 mm rolls with a 10 mm gap, 20° nip and μ = 0.25, 60 rpm, 0.6 m wide on 1.6 t/m³ material.
Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.