FireCADCalc

Hydrocyclone Cut Size by Plitt's Model

Corrected cut size d50c of a hydrocyclone by Plitt's model from cyclone, inlet, vortex finder and apex diameters, vortex height, flow and slurry properties.

Inputs

Examples: 250 mm cyclone, 1,500 L/min, 15 % solids by volume660 mm cyclone on ball mill discharge100 mm desliming cyclone, calibrated F1

Results

Plitt's model is empirical, fitted to a large database; calibrate F1 from a survey of the actual cyclone for design work. The corrected cut size excludes the fines that short-circuit with the underflow water.

Corrected cut size86.774µm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 250 mm cyclone, 1,500 L/min, 15 % solids by volume. The inputs, in the units selected above:

InputValue
Cyclone inside diameter25.400 cm
Inlet diameter (or sqrt(4A/π))6.5000 cm
Vortex finder diameter9.0000 cm
Apex (spigot) diameter5.0000 cm
Free vortex height (vortex finder to apex)90.000 cm
Feed slurry flow1,500.0 L/min
Feed solids by volume15.000 %
Liquid viscosity1.0000 cP
Solids density2.7000 g/cm³
Hydrodynamic exponent (0.5 laminar)0.50000 -
Calibration factor for the material (1 if untested)1.0000 -

Applying the formula below gives:

ResultValue
Corrected cut size39.534 µm

Open this example in the calculator and change any input.

Formula

\(d_{50c} = \frac{F_1\,39.7 D_c^{0.46} D_i^{0.6} D_o^{1.21}\eta^{0.5} e^{0.06 C_v}}{D_u^{0.71} h^{0.38} Q_f^{0.45}\left(\frac{\rho_s - 1}{1.6}\right)^k}\)

Variables

Symbol Meaning SI unit
\(D_c\) Cyclone inside diameter m
\(D_i\) Inlet diameter (or sqrt(4A/π)) m
\(D_o\) Vortex finder diameter m
\(D_u\) Apex (spigot) diameter m
\(h\) Free vortex height (vortex finder to apex) m
\(Q_f\) Feed slurry flow m³/s
\(C_v\) Feed solids by volume -
\(\eta\) Liquid viscosity Pa·s
\(\rho_s\) Solids density kg/m³
\(k\) Hydrodynamic exponent (0.5 laminar) -
\(F_1\) Calibration factor for the material (1 if untested) -
\(d_{50c}\) Corrected cut size m

Method and standards

Plitt's modified cut-size model.

Where it is used

  • Selecting cyclone geometry for grinding circuits.
  • Estimating the effect of apex and vortex-finder changes.

Common mistakes

  • Entering solids by mass instead of by volume.
  • Using millimetres instead of centimetres.

Assumptions and limits

  • Plitt's database range.

References

  • Wills and Finch
  • Wills' Mineral Processing Technology
  • 8th ed. (Butterworth-Heinemann, 2016)
  • ch. 9
  • eq. 9.22 (Plitt, 1976; Flintoff et al., 1987)

Questions and answers

Why does the solids content matter so much?

The cut size grows exponentially with the volume of solids: a dense feed hinders settling and pushes coarser particles to the overflow.

What is F1?

A material factor found by surveying the real cyclone; 1 uses Plitt's database average.

What do the defaults represent?

A 250 mm cyclone with 65 mm inlet, 90 mm vortex finder, 50 mm apex and 900 mm free vortex, fed 1,500 L/min at 15 % solids by volume of 2.7 g/cm³.

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.