FireCADCalc

Minimum Sample Mass by Gy's Sampling Equation

Minimum sample mass for a required precision by Gy's fundamental sampling error, from top size, size range, liberation size, mineral content and densities.

Inputs

Examples: Wills Example 3.3: lead ore, 25 mm crusher productSame ore ground to 150 µm (Wills)Copper ore, 10 mm, chalcopyrite 2 %Gold ore, 2 mm, 5 g/t free gold

Results

Gy's equation estimates only the fundamental error; Wills recommends at least doubling the mass for distribution, preparation and analysis errors. For a 95 % confidence of ±x, enter σ = x / 2 (relative to the grade).

Size distribution factor0.50000
Liberation factor1.0000
Mineralogical factor118.77g/cm³
Sampling constant29.693g/cm³
Minimum sample mass0.001002kg
Sample mass with Wills's allowance for other errors0.002004kg

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Wills Example 3.3: lead ore, 25 mm crusher product. The inputs, in the units selected above:

InputValue
Top size (95 % passing)25.000 mm
Lower size (5 % passing)1.0000 mm
Liberation size150.00 µm
Mineral content (mass fraction)5.8000 %
Density of the valuable mineral7.6000 g/cm³
Density of the gangue2.6500 g/cm³
Particle shapeMost ores (f = 0.5)
Required relative standard deviation1.0000 %
Mass of the lot sampled1,000.0 t

Applying the formula below gives:

ResultValue
Size distribution factor0.25000
Liberation factor0.077460
Mineralogical factor118.77 g/cm³
Sampling constant1.1500 g/cm³
Minimum sample mass179.66 kg
Sample mass with Wills's allowance for other errors359.31 kg

Open this example in the calculator and change any input.

Formula

\(\sigma^2 = \left(\frac{1}{m_s} - \frac{1}{M}\right) C d^3, \quad C = f g l m, \quad l = \sqrt{L/d}, \quad m = \frac{1 - a}{a}\left[(1 - a)\rho_r + a\rho_t\right]\)

Variables

Symbol Meaning SI unit
\(d_{95}\) Top size (95 % passing) m
\(d_5\) Lower size (5 % passing) m
\(L\) Liberation size m
\(a\) Mineral content (mass fraction) -
\(\rho_r\) Density of the valuable mineral kg/m³
\(\rho_t\) Density of the gangue kg/m³
\(\text{ore}\) Particle shape -
\(\sigma\) Required relative standard deviation -
\(M\) Mass of the lot sampled kg
\(g\) Size distribution factor -
\(l\) Liberation factor -
\(m\) Mineralogical factor kg/m³
\(C\) Sampling constant kg/m³
\(m_s\) Minimum sample mass kg
\(2m_s\) Sample mass with Wills's allowance for other errors kg

Method and standards

Gy's fundamental sampling error.

Where it is used

  • Designing sampling protocols for plant feed and concentrates.
  • Deciding where to crush before splitting.

Common mistakes

  • Using d50 instead of the top size.
  • Forgetting the other sources of sampling error.

Assumptions and limits

  • Two-component ore; Gy's factor values.

References

  • Wills and Finch
  • Wills' Mineral Processing Technology
  • 8th ed. (Butterworth-Heinemann, 2016)
  • ch. 3
  • eqs. 3.4-3.6 (Gy, 1967, 1982) and Example 3.3

Questions and answers

Why does the top size matter so much?

The error varies with the cube of the particle size; crushing a sample before splitting it reduces the mass needed by orders of magnitude.

What precision should I enter?

The relative standard deviation: for ±0.1 % Pb at 95 % confidence on a 5 % Pb ore, 2σ = 0.02, so σ = 1 %.

What do the defaults represent?

Wills's Example 3.3: 5 % Pb ore (5.8 % galena), crushed to 25 mm, galena liberated at 150 µm, σ = 1 %; Wills gets 177 kg with a rounded factor m.

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.