FireCADCalc

Two-Stage Flotation Circuit Recovery with Recycle

Overall recovery of a valuable mineral and gangue, separation efficiency and circulating load of a rougher–cleaner or cleaner–scavenger circuit with recycle.

Inputs

Examples: Rougher-cleaner, cleaner tails to rougherCleaner with cleaner-scavengerRougher-cleaner on coal (Wills ch. 10)

Results

Steady state with recycled material assumed to float like fresh feed (Wills notes this exaggerates the gain). Stage recoveries come from bank kinetics or plant surveys.

Circuit recovery of the valuable mineral94.751%
Circuit recovery of gangue21.053%
Separation efficiency73.698%
Circulating load of the valuable mineral (recycle / feed)4.9869%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Rougher-cleaner, cleaner tails to rougher. The inputs, in the units selected above:

InputValue
CircuitRougher–cleaner, cleaner tails to rougher feed
Stage 1 recovery of the valuable mineral (rougher or cleaner)92.000 %
Stage 2 recovery of the valuable mineral (cleaner or scavenger)85.000 %
Stage 1 recovery of gangue20.000 %
Stage 2 recovery of gangue30.000 %

Applying the formula below gives:

ResultValue
Circuit recovery of the valuable mineral90.719 %
Circuit recovery of gangue6.9767 %
Separation efficiency83.743 %
Circulating load of the valuable mineral (recycle / feed)16.009 %

Open this example in the calculator and change any input.

Formula

\(R_{circ} = \frac{R_1R_2}{1 - R_1 + R_1R_2}\ (\text{rougher–cleaner}), \quad R_{circ} = \frac{R_1}{1 - R_2(1 - R_1)}\ (\text{cleaner–scavenger})\)

Variables

Symbol Meaning SI unit
\(\text{circuit}\) Circuit -
\(R_{1A}\) Stage 1 recovery of the valuable mineral (rougher or cleaner) -
\(R_{2A}\) Stage 2 recovery of the valuable mineral (cleaner or scavenger) -
\(R_{1B}\) Stage 1 recovery of gangue -
\(R_{2B}\) Stage 2 recovery of gangue -
\(R_A\) Circuit recovery of the valuable mineral -
\(R_B\) Circuit recovery of gangue -
\(SE\) Separation efficiency -
\(CL_A\) Circulating load of the valuable mineral (recycle / feed) -

Method and standards

Mass balance around a two-stage circuit.

Where it is used

  • Flowsheet selection.
  • Estimating the effect of an extra cleaner or scavenger.

Common mistakes

  • Using circuit recoveries as stage recoveries.
  • Forgetting the extra volume for the circulating load.

Assumptions and limits

  • Recycle floats like fresh feed.

References

  • Wills and Finch
  • Wills' Mineral Processing Technology
  • 8th ed. (Butterworth-Heinemann, 2016)
  • ch. 10
  • eqs. 10.5-10.6 and ch. 12
  • eqs. 12.48-12.50

Questions and answers

Why recycle the cleaner tails?

They still hold valuable mineral; returning them gives it another chance and raises circuit recovery above the single-pass value.

What does the circulating load show?

How much valuable mineral cycles inside the circuit; high loads raise selectivity but need cell and pump capacity.

What do the defaults represent?

A rougher recovering 92 % of the mineral and 20 % of the gangue, and a cleaner recovering 85 % and 30 %.

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.