FireCADCalc

Flotation Bubble Surface Area Flux and Rate Constant

Superficial gas velocity, bubble surface area flux Sb from the Sauter bubble size, and the pulp and overall flotation rate constants k = P Sb Rf.

Inputs

Examples: 38 m3 cell, 15 m3/min air over 10 m2, D32 1.5 mmCoarse bubbles without frother, 4 mmColumn cell, 1.2 cm/s, 1 mm bubbles

Results

P is a floatability factor fitted from plant or pilot data; the k–Sb relation is largely empirical. Frother reduces D32 to about 1 mm, raising Sb several-fold.

Superficial gas velocity1.2000cm/s
Bubble surface area flux71.9981/s
Pulp-zone rate constant1.72801/min
Overall rate constant1.03681/min

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 38 m3 cell, 15 m3/min air over 10 m2, D32 1.5 mm. The inputs, in the units selected above:

InputValue
Air flow to the cell15.000 m³/min
Cell cross-sectional area10.000 m²
Sauter mean bubble diameter1.5000 mm
Floatability (calibrated)5.0000e-04 -
Froth zone recovery50.000 %

Applying the formula below gives:

ResultValue
Superficial gas velocity2.5000 cm/s
Bubble surface area flux100.00 1/s
Pulp-zone rate constant3.0000 1/min
Overall rate constant1.5000 1/min

Open this example in the calculator and change any input.

Formula

\(J_g = \frac{Q_g}{A}, \quad S_b = \frac{6J_g}{D_{32}}, \quad k = P S_b R_f\)

Variables

Symbol Meaning SI unit
\(Q_g\) Air flow to the cell m³/s
\(A\) Cell cross-sectional area m²
\(D_{32}\) Sauter mean bubble diameter m
\(P\) Floatability (calibrated) -
\(R_f\) Froth zone recovery -
\(J_g\) Superficial gas velocity m/s
\(S_b\) Bubble surface area flux 1/s
\(k_p\) Pulp-zone rate constant 1/s
\(k\) Overall rate constant 1/s

Method and standards

Gas dispersion and flotation kinetics.

Where it is used

  • Benchmarking cell aeration.
  • Troubleshooting low flotation rates.

Common mistakes

  • Using the impeller area instead of the cell area.
  • Mixing cm/s and m/s.

Assumptions and limits

  • Empirical P; uniform aeration.

References

  • Wills and Finch
  • Wills' Mineral Processing Technology
  • 8th ed. (Butterworth-Heinemann, 2016)
  • ch. 12
  • eqs. 12.7
  • 12.29 and 12.32-12.33

Questions and answers

Why does bubble size matter so much?

For the same air rate, 1 mm bubbles give four times the surface of 4 mm bubbles, and the rate constant rises in proportion.

What is the froth recovery?

The fraction of particles reaching the froth that survive to the concentrate launder; it falls with deep, stable froths.

What do the defaults represent?

15 m³/min of air over a 10 m² cell (Jg 2.5 cm/s) with 1.5 mm bubbles, P = 0.0005 and 50 % froth recovery.

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.