FireCADCalc

Open Channel Flow by Manning's Equation

Flow and velocity in a rectangular, trapezoidal or part-full circular channel or drain by Manning's equation, with the hydraulic radius and Froude number.

Inputs

Examples: Concrete rectangular drain 0.6 m wide, 0.3 m deep, slope 1 in 500Earth trapezoidal channel, 1 m base, 1.5:1, 0.4 m deep, 1 in 1 000600 mm concrete pipe, 40 % full (240 mm), 1 in 300

From a hydraulics table for the lining; smooth concrete is lower than earth or rubble.

Results

Uniform steady flow; Manning's equation in SI units (n in s/m^(1/3)).

Flow area0.64000m²
Wetted perimeter2.4422m
Hydraulic radius0.26206m
Mean velocity0.51799m/s
Flow0.33152m³/s
Froude number0.30668

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Concrete rectangular drain 0.6 m wide, 0.3 m deep, slope 1 in 500. The inputs, in the units selected above:

InputValue
Channel shapeRectangular
Bottom width (rectangular, trapezoidal)0.60000 m
Side slope, horizontal per 1 vertical (trapezoidal)0 -
Pipe diameter (circular)600.00 mm
Flow depth0.30000 m
Manning roughness coefficient0.013000 -
Bed slope0.20000 %

Applying the formula below gives:

ResultValue
Flow area0.18000 m²
Wetted perimeter1.2000 m
Hydraulic radius0.15000 m
Mean velocity0.97118 m/s
Flow0.17481 m³/s
Froude number0.56621

Open this example in the calculator and change any input.

Formula

\(v = \frac{1}{n} R^{2/3} S^{1/2}, \quad R = A/P\)

\(Q = v A\)

\(Fr = \frac{v}{\sqrt{g A / T}}\)

Variables

Symbol Meaning SI unit
\(\text{shape}\) channel shape -
\(b\) bottom width m
\(z\) side slope (H per 1 V) -
\(D\) pipe diameter m
\(y\) flow depth m
\(n\) Manning roughness s/m^(1/3)
\(S\) bed slope -
\(A\) flow area m²
\(P\) wetted perimeter m
\(R\) hydraulic radius m
\(v\) mean velocity m/s
\(Q\) flow m³/s
\(Fr\) Froude number -
\(T\) top width m
\(g\) standard gravity m/s²

Method and standards

Manning's empirical equation for uniform flow, in SI units. Area, wetted perimeter and top width come from the section geometry; for a part-full pipe the central angle θ = 2 arccos(1 − 2y/D).

Where it is used

  • Sizing storm drains and plant trenches.
  • Checking cooling water return channels.
  • Checking part-full sewer pipes.

Common mistakes

  • Using the full-pipe formula for a part-full pipe.
  • Using n for a new surface on an old channel.
  • Mixing slope in % and m/m.

Assumptions and limits

  • Uniform, steady flow; slope and section constant along the reach.

References

  • Manning's equation (SI)

Questions and answers

What does a 600 × 300 mm concrete drain at 1 in 500 carry?

About 0.175 m³/s at 0.97 m/s with n 0.013.

Is Manning's n in SI the same as in US units?

Yes, the n values are the same; only the constant differs (1 in SI, 1.49 in US units).

What does the Froude number show?

Below 1 the flow is tranquil (subcritical); above 1 it is rapid and a hydraulic jump can form downstream.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.