FireCADCalc

Sorbent Ca/S, Calcination Loss and Sulfation Credit

Ca/S molar ratio of a limestone feed, the heat lost to calcining CaCO₃ and MgCO₃, and the heat gained by sulfation, as percentages of fuel heat (Basu Eqs. 6.1–6.5).

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationChemical and fertiliserPulp and paperBoiler

Inputs

Examples: 6 t/h limestone for 60 t/h of 2 % S coalLignite 4 % S

Results

Excess limestone raises the calcination loss and ash; optimise Ca/S against the SO₂ limit.

Ca/S molar ratio1.3213
Calcination loss (CaCO₃ + MgCO₃)2.1276%
Sulfation credit3.7146%
Net loss-1.5870%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 6 t/h limestone for 60 t/h of 2 % S coal. The inputs, in the units selected above:

InputValue
Limestone feed6.0000 t/h
CaCO₃ in limestone90.000 %
MgCO₃ in limestone3.0000 %
Fuel feed60.000 t/h
Sulphur in fuel (as fired, same basis as the HHV)2.0000 %
Fuel HHV20.000 MJ/kg
Sulphur capture90.000 %

Applying the formula below gives:

ResultValue
Ca/S molar ratio1.4415
Calcination loss (CaCO₃ + MgCO₃)0.85099 %
Sulfation credit1.3627 %
Net loss-0.51170 %

Open this example in the calculator and change any input.

Formula

\(\frac{Ca}{S} = \frac{\dot m_{ls}x_{CaCO_3}/M_{CaCO_3}}{\dot m_fS/M_S}, \quad L_{calc} = \frac{\dot m_{ls}(1830x_{CaCO_3} + 1833x_{MgCO_3})}{\dot m_f HHV}, \quad G_{sulf} = \frac{E_{sor}S\cdot15\,141}{HHV}\)

Variables

Symbol Meaning SI unit
\(\dot m_{ls}\) Limestone feed kg/s
\(x_{CaCO_3}\) CaCO₃ in limestone -
\(x_{MgCO_3}\) MgCO₃ in limestone -
\(\dot m_f\) Fuel feed kg/s
\(S\) Sulphur in fuel -
\(HHV\) Fuel HHV J/kg
\(E_{sor}\) Sulphur capture -
\(Ca/S\) Ca/S molar ratio -
\(L_{calc}\) Calcination loss (CaCO₃ + MgCO₃) -
\(G_{sulf}\) Sulfation credit -
\(L_{net}\) Net loss -

Method and standards

Basu's Eqs. (6.1)–(6.5) (kJ/kg), with IUPAC molar masses for CaCO₃ and S. The net loss is calcination less sulfation; a negative value means the sulfation heat exceeds the calcination heat (a small gain).

Where it is used

  • CFB efficiency calculations (ASME PTC 4 style).
  • Limestone optimisation.

Common mistakes

  • Counting MgCO₃ as sorbent.
  • Ignoring the sulfation credit.

Assumptions and limits

  • Heats per kg of carbonate and of sulphur as given by Basu.
  • The CaCO₃ and MgCO₃ shares together must not exceed 100 % of the limestone.
  • The sensible heat carried away by spent sorbent and extra ash is not included; count it with the ash loss.
  • Sulphur as fired, on the same basis as the HHV.

References

  • Basu
  • Circulating Fluidized Bed Boilers: Design
  • Operation and Maintenance (Springer, 2015)
  • ch. 6
  • Eqs. (6.1)–(6.5): 1 830 and 1 833 kJ/kg for calcining CaCO₃ and MgCO₃; 15 141 kJ/kg S for sulfation

Questions and answers

What Ca/S is typical?

1.5–2.5 for 90 % capture in CFB boilers; bubbling beds need more.

Why does limestone cost efficiency?

Calcination absorbs heat; sulfation gives some back, but excess lime and its ash carry heat away.

Is MgCO₃ useful?

No: it calcines (losing heat) but MgO does not capture sulphur at boiler conditions.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.