Worked example
Example: 6 mm char, 5 kPa O2, 900 °C. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Char particle diameter | 6.0000 mm |
| Local bed voidage | 80.000 % |
| Gas–char slip velocity | 1.0000 m/s |
| Gas density | 0.31000 kg/m³ |
| Gas viscosity | 0.044000 cP |
| Oxygen diffusivity in the gas | 2.0000e-04 m²/s |
| Oxygen partial pressure in the bulk gas | 5.0000 kPa |
| Mean film temperature | 900.00 °C |
| Mechanism factor (1 CO₂, 2 CO) | 1.0000 - |
Applying the formula below gives:
| Result | Value |
|---|---|
| Particle Reynolds number | 42.273 |
| Schmidt number | 0.70968 |
| Sherwood number | 6.0739 |
| Mass transfer coefficient, kg C/(m²·s·kPa O₂) | 2.4910e-04 |
| Diffusion-limited burning rate | 4.4837 kg/(m²·h) |
| Carbon burnt per particle | 0.50710 g/h |
Open this example in the calculator and change any input.
Formula
\(Sh = 2\varepsilon + 0.69\left(\frac{Re}{\varepsilon}\right)^{0.5}Sc^{1/3}, \quad h_m = \frac{12\phi\,Sh\,D_g}{d_cRT_m}, \quad q_d = h_mC_g\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(d_c\) | Char particle diameter | m |
| \(\varepsilon\) | Local bed voidage | - |
| \(U_g - U_c\) | Gas–char slip velocity | m/s |
| \(\rho_g\) | Gas density | kg/m³ |
| \(\mu\) | Gas viscosity | Pa·s |
| \(D_g\) | Oxygen diffusivity in the gas | m²/s |
| \(C_g\) | Oxygen partial pressure in the bulk gas | Pa |
| \(T_m\) | Mean film temperature | K |
| \(\phi\) | Mechanism factor (1 CO₂, 2 CO) | - |
| \(Re\) | Particle Reynolds number | - |
| \(Sc\) | Schmidt number | - |
| \(Sh\) | Sherwood number | - |
| \(h_m\) | Mass transfer coefficient (shown in kg C per m²·s·kPa O₂) | kg/(m²·s·kPa) |
| \(q_d\) | Diffusion-limited burning rate | kg/(m²·s) |
| \(\dot m_p\) | Carbon burnt per particle | kg/s |
Method and standards
Basu's Eqs. (4.7)–(4.10); C_g in kPa, R = 8.314 kPa·m³/(kmol·K).
Where it is used
- Combustion studies and carbon burnout checks.
Common mistakes
- Using O₂ mole fraction instead of partial pressure in kPa.
- Applying outside the fitted size range.
Assumptions and limits
- Diffusion control; spherical char; correlation fitted for 4–12 mm char (a warning appears outside).
- Gas density, viscosity and diffusivity are inputs; take them at the mean film temperature \(T_m\) so the set is consistent.
- The mechanism factor is 1 (CO₂ at the surface) or 2 (CO at the surface); a value between them represents a mixed product.
References
- Basu
- Circulating Fluidized Bed Boilers: Design
- Operation and Maintenance (Springer, 2015)
- ch. 4
- Eqs. (4.7)–(4.10) (Halder and Basu 1988)
Questions and answers
When is combustion diffusion-controlled?
For large char particles at high temperature, where chemistry is faster than oxygen can arrive.
What is the mechanism factor?
1 if carbon burns to CO₂ at the surface, 2 if CO forms there and burns away from it.
Why does Sh start at 2ε?
It is the pure-diffusion limit for a sphere in a bed of voidage ε.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.