Worked example
Example: 6 t/h limestone for 60 t/h of 2 % S coal. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Limestone feed | 6.0000 t/h |
| CaCO₃ in limestone | 90.000 % |
| MgCO₃ in limestone | 3.0000 % |
| Fuel feed | 60.000 t/h |
| Sulphur in fuel (as fired, same basis as the HHV) | 2.0000 % |
| Fuel HHV | 20.000 MJ/kg |
| Sulphur capture | 90.000 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| Ca/S molar ratio | 1.4415 |
| Calcination loss (CaCO₃ + MgCO₃) | 0.85099 % |
| Sulfation credit | 1.3627 % |
| Net loss | -0.51170 % |
Open this example in the calculator and change any input.
Formula
\(\frac{Ca}{S} = \frac{\dot m_{ls}x_{CaCO_3}/M_{CaCO_3}}{\dot m_fS/M_S}, \quad L_{calc} = \frac{\dot m_{ls}(1830x_{CaCO_3} + 1833x_{MgCO_3})}{\dot m_f HHV}, \quad G_{sulf} = \frac{E_{sor}S\cdot15\,141}{HHV}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(\dot m_{ls}\) | Limestone feed | kg/s |
| \(x_{CaCO_3}\) | CaCO₃ in limestone | - |
| \(x_{MgCO_3}\) | MgCO₃ in limestone | - |
| \(\dot m_f\) | Fuel feed | kg/s |
| \(S\) | Sulphur in fuel | - |
| \(HHV\) | Fuel HHV | J/kg |
| \(E_{sor}\) | Sulphur capture | - |
| \(Ca/S\) | Ca/S molar ratio | - |
| \(L_{calc}\) | Calcination loss (CaCO₃ + MgCO₃) | - |
| \(G_{sulf}\) | Sulfation credit | - |
| \(L_{net}\) | Net loss | - |
Method and standards
Basu's Eqs. (6.1)–(6.5) (kJ/kg), with IUPAC molar masses for CaCO₃ and S. The net loss is calcination less sulfation; a negative value means the sulfation heat exceeds the calcination heat (a small gain).
Where it is used
- CFB efficiency calculations (ASME PTC 4 style).
- Limestone optimisation.
Common mistakes
- Counting MgCO₃ as sorbent.
- Ignoring the sulfation credit.
Assumptions and limits
- Heats per kg of carbonate and of sulphur as given by Basu.
- The CaCO₃ and MgCO₃ shares together must not exceed 100 % of the limestone.
- The sensible heat carried away by spent sorbent and extra ash is not included; count it with the ash loss.
- Sulphur as fired, on the same basis as the HHV.
References
- Basu
- Circulating Fluidized Bed Boilers: Design
- Operation and Maintenance (Springer, 2015)
- ch. 6
- Eqs. (6.1)–(6.5): 1 830 and 1 833 kJ/kg for calcining CaCO₃ and MgCO₃; 15 141 kJ/kg S for sulfation
Questions and answers
What Ca/S is typical?
1.5–2.5 for 90 % capture in CFB boilers; bubbling beds need more.
Why does limestone cost efficiency?
Calcination absorbs heat; sulfation gives some back, but excess lime and its ash carry heat away.
Is MgCO₃ useful?
No: it calcines (losing heat) but MgO does not capture sulphur at boiler conditions.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.