FireCADCalc

Void Fraction and Two-Phase Density (Homogeneous and Zivi)

Homogeneous and Zivi void fractions and the two-phase mixture density of steam–water at a pressure and quality, with saturated densities from IF97.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationDistillery and ethanolIAPWS-IF97 (water and steam)Boiler

Inputs

Examples: 70 bar, 10 %10 bar, 5 %

Results

Zivi's slip ratio (ρ_l/ρ_v)^1/3 suits annular-type flow; the homogeneous model assumes no slip.

Saturated water density887.13kg/m³
Saturated steam density5.1454kg/m³
Void fraction, homogeneous90.074%
Mixture density, homogeneous92.693kg/m³
Void fraction, Zivi slip61.983%
Mixture density, Zivi340.45kg/m³

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 70 bar, 10 %. The inputs, in the units selected above:

InputValue
Pressure (absolute)70.000 bar
Steam quality (mass)10.000 %

Applying the formula below gives:

ResultValue
Saturated water density739.72 kg/m³
Saturated steam density36.524 kg/m³
Void fraction, homogeneous69.234 %
Mixture density, homogeneous252.87 kg/m³
Void fraction, Zivi slip45.223 %
Mixture density, Zivi421.72 kg/m³

Open this example in the calculator and change any input.

Formula

\(\alpha = \frac{1}{1 + \frac{1-x}{x}\frac{\rho_v}{\rho_l} S}, \quad \rho = \alpha\rho_v + (1-\alpha)\rho_l, \quad S_Z = (\rho_l/\rho_v)^{1/3}\)

Variables

Symbol Meaning SI unit
\(p\) Pressure (absolute) Pa
\(x\) Steam quality (mass) -
\(\rho_l\) Saturated water density kg/m³
\(\rho_v\) Saturated steam density kg/m³
\(\alpha_h\) Void fraction, homogeneous -
\(\rho_h\) Mixture density, homogeneous kg/m³
\(\alpha_Z\) Void fraction, Zivi slip -
\(\rho_Z\) Mixture density, Zivi kg/m³

Method and standards

Void fraction from the quality and the saturated densities (IAPWS-IF97) with a slip ratio S: S = 1 for the homogeneous model and S = (ρ_l/ρ_v)^1/3 for Zivi; the mixture density is the void-weighted mean. At zero quality the void fraction is zero and the density that of saturated water.

Where it is used

  • Natural circulation design.
  • Drum and riser studies.

Common mistakes

  • Quality by volume entered.

Assumptions and limits

  • Saturated two-phase flow.
  • Zivi's slip is derived for annular flow; in bubbly and churn flow at low quality (typical of risers) it tends to underpredict the void, so the mixture density and circulation head it gives are on the high side. Use a drift-flux model for those regimes.

References

  • Homogeneous model; Zivi (1964) slip S = (ρ_l/ρ_v)^1/3; saturated densities from IAPWS-IF97 (Collier and Thome, Convective Boiling and Condensation)

Questions and answers

Why does a little steam give a large void fraction?

Steam is far less dense than water, so a few per cent by mass fills much of the volume at low pressure.

Which model?

Homogeneous gives the lowest density; slip models give more realistic heads.

Use?

Circulation heads, level measurement and pressure drop.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.