FireCADCalc

Boiler Tube Metal Temperature from Heat Flux

Inside, outside and mean wall temperature of a boiler tube from the fluid temperature, inside film coefficient, scale, wall conduction and outside heat flux.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationPulp and paperFood, dairy and textileBoiler

Inputs

Examples: Furnace wall tube: water 300 °C, h 20 000, 250 kW/m², 63.5 x 6 mm, k 40Same with scale 0.0001 m²K/WSuperheater: steam 480 °C, h 2500, 60 kW/m², 44.5 x 5 mm, k 30

Results

Scale adds more than 10 K to the metal temperature: overheating risk; check the water treatment.

Compare the outside and mean metal temperatures with the allowable temperature of the tube material.

Outside wall temperature (hottest)387.80°C
Mean wall temperature367.02°C
Inside wall temperature346.24°C
Rise across the inside film15.413K
Rise across the scale30.825K
Rise across the wall41.564K

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Furnace wall tube: water 300 °C, h 20 000, 250 kW/m², 63.5 x 6 mm, k 40. The inputs, in the units selected above:

InputValue
Fluid temperature inside the tube300.00 °C
Inside film coefficient20,000 W/(m²·K)
Heat flux on the outside surface250.00 kW/m²
Tube outside diameter63.500 mm
Wall thickness6.0000 mm
Wall thermal conductivity40.000 W/(m·K)
Inside scale (fouling) resistance0 m²·K/W

Applying the formula below gives:

ResultValue
Outside wall temperature (hottest)356.98 °C
Mean wall temperature336.19 °C
Inside wall temperature315.41 °C
Rise across the inside film15.413 K
Rise across the scale0 K
Rise across the wall41.564 K

Open this example in the calculator and change any input.

Formula

\(d_i = d_o - 2w \qquad q_i'' = q''\,\frac{d_o}{d_i} \qquad \Delta T_f = \frac{q_i''}{h_i} \qquad \Delta T_s = q_i''\,R_s \qquad \Delta T_w = \frac{q''\,(d_o/2)\ln(d_o/d_i)}{k_w}\)

\(T_i = T_f + \Delta T_f + \Delta T_s \qquad T_o = T_i + \Delta T_w \qquad T_m = T_i + \frac{\Delta T_w}{2}\)

Variables

Symbol Meaning SI unit
\(T_f\) fluid temperature K
\(h_i\) inside film coefficient W/(m²·K)
\(q''\) heat flux on the outside surface W/m²
\(d_o\) outside diameter m
\(w\) wall thickness m
\(k_w\) wall conductivity W/(m·K)
\(R_s\) scale resistance m²·K/W
\(T_o\) outside wall temperature K
\(T_m\) mean wall temperature K
\(T_i\) inside wall temperature K
\(\Delta T_f\) rise across the film K
\(\Delta T_s\) rise across the scale K
\(\Delta T_w\) rise across the wall K
\(d_i\) inside diameter m
\(q_i''\) flux at the inside surface W/m²

Method and standards

One-dimensional radial conduction with the heat flux referred to the outside surface; film and scale resistances on the inside area.

Where it is used

  • Checking furnace and superheater tubes for overheating.
  • Explaining tube failures after scale build-up.
  • Setting limits for heat flux at low circulation.

Common mistakes

  • Using the average flux where the peak flux is much higher.
  • Ignoring scale or oxide on the inside.
  • Using the conductivity of the wrong material or temperature.

Assumptions and limits

  • Uniform flux around the tube, referred to the outside surface; steady state. Furnace wall tubes are heated on one side with a peak flux at the crown: enter the peak local flux for the hottest point.
  • The mean wall temperature is the arithmetic mean of the inside and outside values.
  • A note appears above about 450 °C on the outside wall.

References

  • Conduction through a cylindrical wall with film and scale resistances in series

Questions and answers

How hot does a furnace tube run?

With water at 300 °C, an inside coefficient of 20 000 W/(m²·K) and 250 kW/m² on a 63.5 × 6 mm tube, the inside wall is 315 °C, the outside 357 °C and the mean 336 °C.

What does scale do?

Just 0.0001 m²·K/W of scale adds about 31 K to the metal at this flux: scale is how clean tubes become overheated tubes.

Which temperature do codes use?

Pressure-part design usually uses the mean wall temperature; oxidation limits use the outside surface. Your code sets which. The mean here is the arithmetic mean of the inside and outside wall temperatures, a close approximation to the mean of the logarithmic profile for boiler tubes.

Method and article reviewed by FireCAD engineering on 11 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.