FireCADCalc

Mechanical Pan Circulator Power and Tip Speed

Installed and average power of a mechanical circulator in a vacuum pan from Hugot's figures per m³ (2.3 and 1.0 kW/m³), with the impeller tip speed checked.

Sugar mill and cogenerationElectric motor

Inputs

Examples: 40 m3 pan, 1.2 m impellerC pan at 50 rpm

Hugot: 80 rpm for a 1.2 m impeller on footings, A and B; 60 for C below 97 brix; 50 above.

Results

Hugot: tip speeds of 5–7.5 m/s for high-purity strikes (6.5 typical), 3.5–5 m/s for low grades; circulators shorten strikes by 15–50 %.

Installed power115.00kW
Average power50.000kW
Tip speed3.6652m/s
Energy per strike400.00kWh

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 40 m3 pan, 1.2 m impeller. The inputs, in the units selected above:

InputValue
Pan working volume40.000 m³
Impeller diameter1.2000 m
Impeller speed80.000 rpm
Installed power per m³2.3000 kW/m³
Average power per m³1.0000 kW/m³
Strike time3.0000 h

Applying the formula below gives:

ResultValue
Installed power92.000 kW
Average power40.000 kW
Tip speed5.0265 m/s
Energy per strike120.00 kWh

Open this example in the calculator and change any input.

Formula

\(P_i = e_i V, \quad P_a = e_a V, \quad v_t = \pi D_i n, \quad E = P_a t\)

Variables

Symbol Meaning SI unit
\(V\) Pan working volume m³
\(D_i\) Impeller diameter m
\(n\) Impeller speed 1/s
\(e_i\) Installed power per m³ W/m³
\(e_a\) Average power per m³ W/m³
\(t\) Strike time s
\(P_i\) Installed power W
\(P_a\) Average power W
\(v_t\) Tip speed m/s
\(E\) Energy per strike J

Method and standards

Hugot's specific powers.

Where it is used

  • Specifying circulators.
  • Energy budgets.

Common mistakes

  • Using installed power as consumption.
  • Too high a tip speed on C strikes.

Assumptions and limits

  • Hugot's specific figures. He also gives a peak of about 1.9 kW/m³; the page shows installed and average power only.
  • The tip speed is compared with Hugot's 3.5–7.5 m/s range.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 33
  • mechanical circulation
  • pp. 707–710

Questions and answers

Why add a circulator?

Low-grade massecuites circulate poorly; a stirrer keeps evaporation up and shortens strikes.

How efficient is it?

Hugot: about 7 % hydraulic efficiency (11 % semi-axial): most power becomes heat in the massecuite.

Which speed?

Slower for viscous low-grade strikes, to limit power and crystal damage.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.