Worked example
Example: Perry 13: 100 mol at 0.18 to 0.06. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Charge mass | 2.3065 kg |
| Strengths entered as | Mole fraction |
| Initial strength of the charge | 18.000 % |
| Final strength in the pot | 6.0000 % |
| Pressure | 101.33 kPa |
Applying the formula below gives:
| Result | Value |
|---|---|
| Initial mole fraction | 18.000 % |
| Final mole fraction | 6.0000 % |
| Moles left in the pot | 69.853 % |
| Residue mass | 1.3760 kg |
| Distillate mass | 0.93048 kg |
| Average distillate mole fraction | 45.805 % |
| Average distillate strength | 75.494 % |
| Ethanol recovered in the distillate | 76.716 % |
Open this example in the calculator and change any input.
Formula
\(\ln\frac{H_i}{H_f} = \int_{x_f}^{x_i}\frac{dx}{y^*(x) - x}, \quad \bar x_D = \frac{H_i x_i - H_f x_f}{H_i - H_f}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(M_i\) | Charge mass | kg |
| \(\text{basis}\) | Strengths entered as | - |
| \(s_i\) | Initial strength of the charge | - |
| \(s_f\) | Final strength in the pot | - |
| \(P\) | Pressure | Pa |
| \(x_i\) | Initial mole fraction | - |
| \(x_f\) | Final mole fraction | - |
| \(H_f/H_i\) | Moles left in the pot | - |
| \(M_f\) | Residue mass | kg |
| \(M_D\) | Distillate mass | kg |
| \(\bar x_D\) | Average distillate mole fraction | - |
| \(\bar q_D\) | Average distillate strength | - |
| \(\eta\) | Ethanol recovered in the distillate | - |
Method and standards
Rayleigh equation integrated by Simpson's rule (200 intervals) on the fitted Wilson equilibrium.
Where it is used
- Pot stills for whisky, rum and brandy.
- Laboratory distillation.
Common mistakes
- Taking first-drop strength as the average.
- Using % vol in a molar balance.
Assumptions and limits
- Wilson energies fitted at 1 atm; 0.9–1.2 atm only.
- Binary ethanol–water; congeners and dissolved solids ignored.
- One equilibrium stage; no reflux.
- Compositions and recovery do not depend on the charge size; with a zero charge the masses are zero.
References
- Ethanol–water VLE at about 1 atm: Wilson equation (Perry's Chemical Engineers' Handbook, 9th ed., sec. 4) with energies 399 and 933 cal/mol fitted to FireCAD ethanol–water x–y–T data at 101.325 kPa; ethanol vapour pressure Perry's 9th ed. Table 2-8; water IAPWS-IF97
- Checked against Gmehling and Onken
- DECHEMA Chemistry Data Series vol. I/1
- as quoted in Perry's 9th ed. sec. 13 (simple batch distillation example)
- Rayleigh equation
- Perry's 9th ed. sec. 13
- Eq. (13-124)
Questions and answers
What does the Rayleigh equation say?
ln(Hi/Hf) is the integral of dx/(y − x) from the final to the initial pot composition.
What is Perry's example?
100 mol at 0.18 boiled down to 0.06 leaves 70 mol; the distillate averages 0.46 mole fraction.
Why is the distillate weaker than the first drops?
The vapour gets weaker as the pot is depleted; the average includes the tail.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.