Worked example
Example: 10 % vol beer to 94 % vol, R = 1.3 Rmin. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Feed strength | 10.000 % |
| Distillate strength | 94.000 % |
| Bottoms strength | 0.10000 % |
| Feed condition (1 saturated liquid, 0 saturated vapour) | 1.0000 - |
| Reflux as a multiple of the minimum | 1.3000 - |
| Pressure | 101.33 kPa |
Applying the formula below gives:
| Result | Value |
|---|---|
| Feed mole fraction | 3.2950 % |
| Distillate mole fraction | 79.830 % |
| Bottoms mole fraction | 0.030938 % |
| Minimum reflux ratio | 2.3120 |
| Reflux ratio | 3.0056 |
| Theoretical stages (reboiler = 1) | 15.815 |
| Feed stage from the top | 9.0000 |
Open this example in the calculator and change any input.
Formula
\(y = \frac{R}{R+1}x + \frac{x_D}{R+1}, \quad \frac{R_{min}}{R_{min}+1} = \max_{x_q \le x < x_D}\frac{x_D - y^*(x)}{x_D - x}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(q_F\) | Feed strength | - |
| \(q_D\) | Distillate strength | - |
| \(q_B\) | Bottoms strength | - |
| \(q\) | Feed condition (1 saturated liquid, 0 saturated vapour) | - |
| \(R/R_{min}\) | Reflux as a multiple of the minimum | - |
| \(P\) | Pressure | Pa |
| \(x_F\) | Feed mole fraction | - |
| \(x_D\) | Distillate mole fraction | - |
| \(x_B\) | Bottoms mole fraction | - |
| \(R_{min}\) | Minimum reflux ratio | - |
| \(R\) | Reflux ratio | - |
| \(N\) | Theoretical stages (reboiler = 1) | - |
| \(N_F\) | Feed stage from the top | - |
Method and standards
McCabe–Thiele stepping from the top with the fitted Wilson equilibrium.
Where it is used
- Rectifying and stripping column design for potable and fuel ethanol.
- Checking the effect of reflux on stages.
Common mistakes
- Taking Rmin at the feed pinch only.
- Specifying distillate above the azeotrope.
Assumptions and limits
- Wilson energies fitted at 1 atm; 0.9–1.2 atm only.
- Binary ethanol–water; congeners and dissolved solids ignored.
- Constant molar overflow; total condenser; saturated reflux. Ethanol–water departs a little from constant molar overflow, so the stage count approximates an enthalpy-balance (Ponchon–Savarit) result.
- The engine accepts the same ranges as the form: q from 0 to 1.5 and 90–125 kPa.
References
- Ethanol–water VLE at about 1 atm: Wilson equation (Perry's Chemical Engineers' Handbook, 9th ed., sec. 4) with energies 399 and 933 cal/mol fitted to FireCAD ethanol–water x–y–T data at 101.325 kPa; ethanol vapour pressure Perry's 9th ed. Table 2-8; water IAPWS-IF97
- Checked against Gmehling and Onken, DECHEMA Chemistry Data Series vol. I/1, as quoted in Perry's 9th ed. sec. 13 (simple batch distillation example)
- McCabe–Thiele method with constant molar overflow (Perry's 9th ed. sec. 13)
Questions and answers
Why is the minimum reflux set by a tangent?
The ethanol–water curve bends towards the diagonal near the top, so the rectifying line touches it above the feed before reaching the q-line.
Why can't the distillate reach 100 %?
The azeotrope at about 0.885–0.89 mole fraction stops ordinary distillation; dehydration needs sieves.
Why are strengths in % vol?
Distillers specify % vol; they are converted to mole fractions with the OIML R 22 densities.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.